Raw Viagra recipe

Discussion in 'Steroid Homebrew' started by tattscp35, Oct 3, 2018.

  1. tattscp35

    tattscp35 Member

    So was doing some research and wondering if I have this info correct when it comes to getting my own raw viagra and capping.

    If my capsule weights .20 empty and I want 50 capsules = .20 x 50 = 10 grams of weight needed.

    Plan is to make them 50mg each so = 50 (mg per) x 50 (number of capsules) = 2500mg/2.5g of raw powder.

    So then I take my 10 grams of total weight - my 2.5g raw powder = 7.5g of filler needed.

    So in short I'll need 2.5g of raw powder and 7.5g of filler to cap 50 pills which are 50mg each???
     
  2. JackSmooth

    JackSmooth Member

    You could fill the cap full of filler, then multiply by total caps and then subtract 2.5 active from that
     
  3. Iron Vett

    Iron Vett Member

    What @JackSmooth said.

    I use size 0 caps. They hold .850 milligrams each of plain filler. I like baking soda.

    50 caps X .050 milligrams= 2.5 grams sildenafil raws

    50 caps times .850 milligrams = 42.5 grams total

    42.5 - 2.5 = 40 grams filler

    Edit: This will probly not be exact but it will be close. You can adjust your filler up or down to get closer to exactly 50 caps per batch each time you make a batch. Each compound will have different ratios of filler to active ingredient due to their varying densities
     
    SuperSwede, Rosconow and JackSmooth like this.
  4. tattscp35

    tattscp35 Member

    Thanks guys. I'll take your tip
     
  5. tattscp35

    tattscp35 Member

    JackSmooth where does the .050 milligrams come from?

     
  6. Iron Vett

    Iron Vett Member

    .050 grams is fifty milligrams. My error

    And .850 grams is 850 milligrams
     
  7. tattscp35

    tattscp35 Member

    Got it thanks!!!
     
  8. The first thread in this section is called “how to cap 101” and the first post answers this question....
     
    Robfromga likes this.
  9. tattscp35

    tattscp35 Member

    Is 0 the most commonly used capsule size used for viagra?
     
  10. Iron Vett

    Iron Vett Member

    Capsule size is more of a personal preference. 0 size is the most commonly used sized so my fat fingers can handle them:D
     
  11. tattscp35

    tattscp35 Member

    Thanks man
     
  12. Rosconow

    Rosconow Member

    I always fill a cap with whatever filler ingredient I'm going to use (try to use similar as active compound) first. Example, l-arginine is granular and heavier as opposed to creatine that is light with small particulate.

    Its so much easier when mixing in the mortar/ pestal, when both filler and active are similar size and weight.
     
  13. tattscp35

    tattscp35 Member

    I've read people use whey protein. Is that not recommended? It's only for person use.
     
  14. Rosconow

    Rosconow Member

    Yes, you can use whey, corn starch, baking soda, creatine, dextrose, pretty much anything for a filler.
     
  15. janoshik

    janoshik Member

    Whey tends to stick and form lumps. Creatine, dextrose or microcrystalline cellulose would be better options.
     
  16. tattscp35

    tattscp35 Member

    Thanks guys
     
  17. Iron Vett

    Iron Vett Member

    I like baking soda for filler because it seems to “suspend” the compound being mixed well and it’s not that “sticky”. By sticky, I’m talking about sticking to the tools your using to mix and cap. I use a compound tumbler that I made and corn starch, for example, sticks to the sides too much to be able to mix properly.

    Baking soda may have a few clumps in it but a pass through a strainer takes care of that.
     
    janoshik and tattscp35 like this.
  18. valuum

    valuum Member

    Not trying to be funny but is the popularity of viagra in the bodybuilding community due to deca-dick side effects, or do people actually use it as a supplement for pumps.
     
  19. master.on

    master.on Member

    Since they're just 50 mg, buy the smallest caps you can get (i.e. size 4 or 5) to use a little filler as possible.

    Weigh empty caps

    Fill in just 10 caps (with bare filler)
    Then weigh each of them with a very accurate scale (i.e. milligram scale)

    Then take the cap weight
    subtract the empty cap weight
    subtract the intended amount (50 mg)
    multiply by the number of caps you want to make
    and you get the total filler weight.


    Some bodybuilders use viagra to afford their GH,
    some bodybuilders use viagra to make a living
    (G4P)
    :p:D:eek::eek::eek:
     
  20. Rosconow

    Rosconow Member

    I don't know about viagra, but i did use cialis @ 5mg for awhile as part of my preworkout routine. Pumps were Anavar-ish, but any kind of cardio where my pant leg rubbed against my member caused a lot of re-adjusting... and or walking away hunched over. Lulu butts don't help either!
     
    An1970 likes this.