MESO-Rx

Anabolic Steroids

300mg/ml test c possible with what?

  • Thread starter Thread starter Deleted member 127229
  • Start date Start date
Deskoze38192 said:
Will do
So far no crashing

Side note: For this tiny brew I used a med lab supply 50 ml Narrow mouth Graduated Erlenmeyer glass Flask ($1.85)
I spray down with bleach water, rinse with distilled water and let dry on the hot plate upside down. Then I throw it away when I’m done. Cheap and easy. The narrow neck worked fine on the magnetic stirrer. 30 ml is the max though, any more and it would be spritzing out. I hate “doing dishes” so just throwing it away when I’m done made me happy lol. Plus I like the narrow neck over the beakers I use for larger brews.
Added raws, Added BA, Added BB and stirred until the raws dissolved while heating. Added MCT and had on the magnetic stirrer for 30 minutes while maintaining heat.
Maintained heat and filtered warm.
Click to expand...
Bleach water? Why not rubbing alc? Bleach water sounds like it could lead to issue?
 
jJjburton said:
Bleach water? Why not rubbing alc? Bleach water sounds like it could lead to issue?
Click to expand...
It’s literally the recommended process in the second paragraph of the homebrewing Bible under “beakers, washing”
10% Bleach water is the first step, not the last step
Then I rinsed the glassware multiple times with distilled water and dried with heat
When I use a beaker I also wash with dish soap after the bleach water, before the rinsing with distilled water part but this was a brand new narrow neck so I chose to skip the dish soap step.
I throw the narrow necks away after use. I wash the beakers and use again
 
Last edited:
I tried it and it turned out great. 6% overdose on raws. Took 40min to dissolve on heated stirrer at 140F. Held at 66F so far.

In mct at 2/21 ba/bb
 
willy86 said:
For me personally, 400 mg/ml remains in solution in the summer, but it is on the razor's edge.
As soon as the temperatures drop a few degrees it crashes
Click to expand...
400mg ml test c? In only ba/bb? How is that possible?
 
willy86 said:
In fact, it didn't hold up much. As long as it was hot outside it held up, but when the outside temperature dropped by a few degrees it crashed
Click to expand...
What temp was it holding and crashing? How many times did you brew it at 400?

Any better luck with 350?

Any pip?
 
Just to be clear there is literally no need to get the solution to the MP of 220 Celsius.

The entire point of solvents is to lower the activation energy of the physical transformation from a solid to a liquid in solution. The Melting Point of a crystalline solid is only relevant when you’re melting it not in a solution. example: when trying to identify compounds via melting point analysis or trying to do a very rudimentary check of a purity.
 
goonr said:
This look alright to you? Just want to make sure i make no mistakes on my first brew.

View attachment 266350
Click to expand...
No brother this is not right. Just do the math on a calculator of what they're telling you to put in and it comes out to be 195ml, but you're only trying to make 150ml. Therefore your dosage is going to end up being around 225mg, and that's just a guess off the top of my head but to answer your question, no this does not look right. Do not use these calculators, they will never give you the proper amounts. Use a pen and paper an your own calculator. It's not hard
 
You must log in or register to reply here.

Similar threads

A
Brewing Test C at 300mg/ml?
2
Replies
21
Views
481
Sampei
Sampei
J
  • Question Question
Bold C 250mg/ml
Replies
3
Views
145
knucklesamich
knucklesamich
B
Using GSO to dilute hormones in MCT
Replies
4
Views
124
Photon
Photon
bigforyouben
First time brewing - Test E
2
Replies
21
Views
857
james13
J
R
Diluting 400 Test E tips? With organic MCT Oil?
Replies
6
Views
226
RichRoider
R

Sponsors

Latest posts

Back
Top