MESO-Rx
Anabolic Steroids
100% ethyl oleate (without carrier oil) recipe (?)
- Thread starter Peter111
- Start date
FR0Z3N_B0MB3RRR
Member
if you read on the sticky threads Xkawn brewing bible or something like this he claims to use 100% EO... i asked him what does exactly mean but he never answered
so i didnt understand if he brewed with 99% EO and 1% BA... or 100% EO withou BA and BB..
Months ago i went on strange recipes, wasted some gears solvent and time..
i would stick with classic ones instead of trying re invent the wheel
To answer you both if going with EO you OBVIOUSLY still need to use BA as EO is just a solvent as is BB. So account for raws displacement then the rest is 99% EO and 1%BB.
FR0Z3N_B0MB3RRR
Member
Yes it appeared obvious to me too... but then that overrated Xkawn writin 100% was in fault..
I would never brew without BA...
i read somewhere that too much EO could make the solution crash... anyway i brew at low concentration.. always smooth pins.. and i pin ED... i ll never understand people who love highly concentrated gear..
I would never brew without BA...
i read somewhere that too much EO could make the solution crash... anyway i brew at low concentration.. always smooth pins.. and i pin ED... i ll never understand people who love highly concentrated gear..
I homebrew everything in 2%BA 20%BB and MCT oil.
The few high concentration products I did were... Test En 400mg/ml,. Masteron En 300mg/ml, EQ 500mg/ml, NPP 150mg/ml, Primo En 200mg/ml, 150 Test PP + 150 Test En, Trestolone Ace 100mg/ml all smooth without pip.
I homebrewed also Stanolone (DHT) in 2% BA 20%BB and Castor/Ricin oil, it's thick AF but holds without any solvents. Not worth using it imho, better to stick to the basics.
Tbh i would avoid completely Ethyl Oleate because it's a bit toxic and you don't really need it for normal concentration gear
I would be curious to use Mig840, but i can't find it in europe...
The few high concentration products I did were... Test En 400mg/ml,. Masteron En 300mg/ml, EQ 500mg/ml, NPP 150mg/ml, Primo En 200mg/ml, 150 Test PP + 150 Test En, Trestolone Ace 100mg/ml all smooth without pip.
I homebrewed also Stanolone (DHT) in 2% BA 20%BB and Castor/Ricin oil, it's thick AF but holds without any solvents. Not worth using it imho, better to stick to the basics.
Tbh i would avoid completely Ethyl Oleate because it's a bit toxic and you don't really need it for normal concentration gear
I would be curious to use Mig840, but i can't find it in europe...
Mig840 is bad too.
How do you rate Mig840?
Same issue. If you do a ultrasensitve c reactive protein test. It will show up with high systemic inflammation. Some worse than others. Best to use mct , grapeseed, seaseme, cottonseed, castor. Can't think of any others.
"eq 500mg/ml; 150 test pp" with carrier oils.. damn, that oils seems to be the real deal; Where do you buy your carrier oils ? (iam from europe too);
why do you still need to use BA ?; i mean i found that EO has "antimicrobial/antibacterial" properties already, or are them not enuff stong ?
Have you ever actually done these tests, and if so how could you possibly isolate all the variables and conclude that it’s the carrier oil causing a rise in crp.
I feel like you’re just blinding following some YouTubers opinion with his main evidence that EO is bad is that it will dissolve/wipe away the black ink on a syringe barrel. This is moronic evidence as BB will do the same thing.
About EO i found "Ethyl oleate is not currently approved by the U.S. Food and Drug Administration for any injectable use. However, it is used by compounding pharmacies as a vehicle for intramuscular drug delivery, in some cases to prepare the daily doses of progesterone in support of pregnancy"
and
"Ethyl oleate is produced by the body during ethanol intoxication. Ethyl oleate is used as a solvent for pharmaceutical drug preparations involving lipophilic substances such as steroids. It also finds use as a lubricant and a plasticizer"
so i would say that probably has to do with mainly that robber being worn out and move on to the product rather than the quantity/local of EO (?)
I have only done one test with eo and anadrol. So I can not definitively say it was caused by EO. But I have seen the video you are referring to. I think it much smarter and safer to stick with what FDA has approved and is used in pharmaceutical settings. I brew with mct oil. it will cause the ink to rub off the syringe also. but I dont have a high crp when using any of my compounds.
Can you post the link of the video ?
Why do i need BA ? Dont EO already has "antimicrobial/antibacterial" properties already, or are them not enuff strong ?
Last edited:
You need ba, 1% will be just fine.
BigDaddyV
Member
Mig840 sucks
I buy MCT and Safflower oil from Amazon...
I use MCT oil by now nutrition.
Remember that we make everything sterile both with BA and Filtering...
The real deal on brewing is:
-quality of gear
-no pip
-no lumps (i injected 3ml of Primo 200 in my butt and I have a bit of inflammation
)-Concentration, it can fit better your injection schedule, going high isn't that useful except for Primo.
-Price, a bottle of test cost something like 3euros? Lol
