How to finish unfinished raws?

[MFAAS]

Can somebody point me to a resource about unfinished raws? From what I can tell, it seems like it's just bulk product that has been pre-mixed. As far as I can tell, the remaining steps are:

1. Sterilize the vials

2. Fill them while filtering through a micron wheel filter

3. Put on the stopper

Is that correct? Basically they're just trying to take the mixing and measuring steps out of it for everyone? I am only asking as I am not able to make international orders for a while and am struggling to find a domestic source for raws that seems trustworthy. So I was looking at some unfinished oils from a couple sources and just want to be sure I fully understand what would be needed.

Thanks yall! Sorry if this is a total n00b question. I searched here and Used TFSE, but couldn't find anything outlining the details I'm looking for.

 

[eery]

are you talking about unfiltered gear or raws? i dont quite get what you mean by "unfinished raws".

If its raws, they need to be suspended in ba/bb/oil, filtered and then put in vials and you have your finished product.


If its just mixed up ba/bb/oil/raws, you just have to filter it.

 

[MFAAS]

That's what I am trying to figure out. For example, this product: Dragon Ordnance

I don't understand exactly what step of the process these are at/what is remaining for the buyer to do to get it into a usable product.

 

[Ridethelightningbarefoot]

Nah thats unfinished oil. Raws well there raws to say there unfinished is redundant. Not trying to be a dick but you may not get the help and info you need if you dont use the correct terms (talking to suppliers and the like). All you have to do with that shit is filter it. I always recomend getting pre sterilized vials and filtering directly into them this will give you the best sterile isolation unless you have a clean room or a flow hood. The only time I would sterilize and seal the vials myself is if I had a flow hood or if I was a underground lab that had to crank out a bunch of product

 

[MadBret]

That's what I am trying to figure out. For example, this product: Dragon Ordnance

I don't understand exactly what step of the process these are at/what is remaining for the buyer to do to get it into a usable product.

The oils contain the raw, ba, and bb. It still has to be filtered into sterile containers before it is ready for injection.

Basically, the hard part of brewing your own gear is what is left to do when you order semi finished injectables.

Just buying raws and brewing it yourself isn't much more work than filtering semi finished oils. You would get more for your money if you just bought raws.

 

[MFAAS]

Thanks yall. I have no hesitation or qualms with doing the process myself, I've performed much harder chemical procedures before. Just struggling to find that, but will keep looking. If I can find a decent domestic source for raw powders I would gladly homebrew from scratch.

So that's "unfinished oil" is basically just bulk finished product that simply needs to be filtered and packed into individual vials. That seems pretty straightforward, though obviously I am sure quality can be better with homebrew as well as being confidence of the concentration of the product since you make it yourself.

As far as the terminology "unfinished raws" - I was looking at some other source that literally used that exact term. Not sure which, I see now that Dragon Ordnance doesn't use that term. Regardless, my bad any confusion.

 

[Ridethelightningbarefoot]

Thanks yall. I have no hesitation or qualms with doing the process myself, I've performed much harder chemical procedures before. Just struggling to find that, but will keep looking. If I can find a decent domestic source for raw powders I would gladly homebrew from scratch.

So that's "unfinished oil" is basically just bulk finished product that simply needs to be filtered and packed into individual vials. That seems pretty straightforward, though obviously I am sure quality can be better with homebrew as well as being confidence of the concentration of the product since you make it yourself.

As far as the terminology "unfinished raws" - I was looking at some other source that literally used that exact term. Not sure which, I see now that Dragon Ordnance doesn't use that term. Regardless, my bad any confusion.

I dont think you will ever achieve pharm quality because of sterility and raws quality. Until we have access to more and better testing you can really only trust testosterone raws. Everything else about the homebrew process is straight forward. Its the things we cant control that fuck the homebrewer in the ass but you have even less control when you buy pre made