Quad injection pin size?

[havana]

Hello, I have a 22G 1 1/2" pin, is this to long for a quad shot or should I go with a 1" pin. I will be using Primobolan oil base.

 

[pump55]

Bro, never tried a 1 1/2 pin in the quad but if you do let me know how it felt. I always use a 1inch 22g.
Good Luck

 

[mid life crisis]

gauge...

Bro, never tried a 1 1/2 pin in the quad but if you do let me know how it felt. I always use a 1inch 22g.
Good Luck

23-25 guage 1" in the quad. Save the 1.5" for the butt

 

[madman]

A 25ga 1" always worked for me. I did my very first cycle with 23ga 1.5" and had no problems with those either.

 

[Adogg4]

bro if thats all you have just put the needle in only 2/3 of the way

 

[Pred]

Unless you have skinny little legs a 1 1/2 inch will be fine.

 

[zman12]

When I used to do alot of quad injections I always used 23G 1" and they seemed to work fine for me.

 

[jayce]

Bro,
I always use 1.5 inch pins in the quad. You got alot of meat there. Dont worry about it. 1 inch is fine too but I wouldn't use anything less than an inch.

Happy stabbing,
Jayce

 

[nandro]

22ga 1 1/2 is okay. if ya scared...cut a cap about a half inch long and cap the needle. this turns it into a 1 inch so you won't drop it down to the hub when you push the plunger. i always say this after all the years of use. go with the smallest gauge possible but go deep near the bone. better blood supply with less scar tissue. if you a newbie do the 1 inchers until you get alot of scar tissue. when you get alot of crunchin when ya insert the needle it's time to go deeper where there is a better blood supply. this is the trailer trash style!! lol

Bro,
I always use 1.5 inch pins in the quad. You got alot of meat there. Dont worry about it. 1 inch is fine too but I wouldn't use anything less than an inch.

Happy stabbing,
Jayce

 

[PUMPED]

if you have some meat on your legs you will be fine with even 21 G 1.5 inch, i used them for a while....

 

[jayce]

22ga 1 1/2 is okay. if ya scared...cut a cap about a half inch long and cap the needle. this turns it into a 1 inch so you won't drop it down to the hub when you push the plunger. i always say this after all the years of use. go with the smallest gauge possible but go deep near the bone. better blood supply with less scar tissue. if you a newbie do the 1 inchers until you get alot of scar tissue. when you get alot of crunchin when ya insert the needle it's time to go deeper where there is a better blood supply. this is the trailer trash style!! lol

Just a warning if you decide to use the cut cap method. BE CAREFUL not to ruin your sterile field when recapping. I doubt you have sterile scissors to make the cut with so if you touch any portion of the needle with the cap you have contaminated your needle.
Jayce

 

[graybass]

You guys are all animals!!
Anybody ever use the old Sus redi-jects. Think they were 21guage 2"
I don't remember for sure, cause as soon as I saw them I transfered them to a smaller syringe. Try driving that into your Quad!!!!
I did it one time only!

 

[BoogerSnax]

I use 25g 5/8" or 1" on my quads. I draw with a larger needle and inject with the 25g.

PEACE

 

[Joker]

Bro,
I always use 1.5 inch pins in the quad. You got alot of meat there. Dont worry about it. 1 inch is fine too but I wouldn't use anything less than an inch.

Happy stabbing,
Jayce

What jayce said.