Test C Deca blend question

[Gramps]

If one were to brew up a blend of 200 mg/ml test c plus 100-200 mg/ml deca in GSO, would the standard 18%BB and 2% BA still hold? I've read that deca doesn't need BB so my thinking this mix is good.

My home made handy dandy spreadsheet shows for 100ml of 200 TC, 100 Deca: 20G TC, 10G D, 2ml BA, 18ml BB, 52.2ml oil. That's with powder displacements of TC .909 and Deca .962. Anyone care to comment?

I kept it simple above but I also programmed it for purity, in this case using 85% as a guesstimate for the same batch I get: 25.53G TC, 11.76G Deca, 2ml BA, 18ml BB, and 47.29ml oil for a hopeful dose oof 200/100 but an indicated dose of 253.3/117.6 for those keeping score or might find use in this. Of course if the BB won't hold the added deca, ALL of this will change and that's where I can use some input. Why do I want to do this? 1 because I can, 2, it saves guessing the amount of deca to add to a pin already loaded with test. This will be an occasional use item.

 

[XKawN]

Deca still needs bb. You may be thinking of eq. If Cyp is hard to keep in solution by its self I would imagine adding the deca would make it probably impossible at the ratio and solvents your talking...

 

[Gramps]

I was definitely thinking Deca, but like all things, I've seen it go both ways with some claiming No bb, others claiming the standard 18%. It may have been basskiller showing none needed.

Is there a reasonable way to blend these at 200/100? It just seems logical but if I have to kill it with BB and make it suck to use, it wouldn't be worth it. Of course I could likely do 100/50 and double the dose I suppose... (simply put, I don't need the high doses of deca many others use)

 

[mghoward74]

I personally don't care for blends. Let's say later on down the line you want more or less of one compound....what are you going to do now? Nothing, just suck it up & stick it out.

Now if I were to consider it, here's a few that I would consider

Low dose of TPP w/Test Undecylenate/iso.
*Reason, vacation*

EQ 250 & TREN E 150
TrenA/NPP/TPP
MastE/EQ/Deca or tren

I think you'd like it more if TC was 100 & Deca was 200.

And your BB is total, not per

 

[XKawN]

It would be doable if you would use enanthate. That's what I'd do if I had to do a blend of test and deca.

 

[Gramps]

I won't use this blend on its own, just a substitute at times when I add deca and I plan to keep the batches small if I go that route. I agree on the BB total and not per, which is why I considered T at 100 and D at 50 for a load of 150 versus the 300 total I started this discussion with which is too heavy for 18%BB. I only want the minimum in Decal as I already have issues retaining water with a script for that. Remember, I'm not cycling, I'm TRTing adding a touch of Deca for joint relief. Nothing more, so the general rules of gains and all don't apply here as they would to most of you. Doing these small amounts make dosing Deca into an already T loaded pin a hit or miss deal in accuracy so I'm kicking around a blend to keep the numbers in control. Thanks for the input.

 

[mghoward74]

If water gains are an issue consider NPP & TPP. You can make both at 100 each (or 75mg) and pin it M,TH, SAT.

That way you'll get a near trt dose, plus the joint relief of npp, if your trt is script, then save it and stock pile it for later use.

Hopefully, this is an alternative