Test cyp brew

[Ridethelightningbarefoot]

I just recently brewed test cyp at 250mg/ml.
1ba
10bb
The rest powder and mct oil totaling 40ml. Filtered with ptfe .22um and baked 250f for 30 mins.

I am pinning with bold cyp. 1 ml test c and 1.4ml bold cyp. The bold cyp I had sterility issues with that were reaolved with refiltering and baking. I pinned delt, quad and glute. Delt had a raised bump like a grape lots of pip. Quad had a knot and lots of pip. Glute has no knot just a ton of pip. Trying to figure out where issue is.

 

[Notadouche]

Right of the bat I’m pretty surprised you got t-c to hold @250 in mct with only 10%bb. I definitely can’t do that with mct or mig 840 where I’m at.

Did it crash at all? I’ve had t-c I had to heat every so often when it crashed because I pushed the concentration/lack of bb.

Without knowing any other details I’d wonder if the t-c is crashing in depot.

 

[Ridethelightningbarefoot]

https://photos.app.goo.gl/8STQCemwSXcBqKnB9

Can you see that?

 

[Iron Vett]

https://photos.app.goo.gl/8STQCemwSXcBqKnB9

Can you see that?

It’s hard to tell but it looks like I see hormone swirls in the light and it also looks like the vial was possibly laying on its side and some hormone may have settled down and is showing on the side toward the camera. But it really is hard to make these things out in photos.

Personally I never use less than 18%bb for test cyp due to the fact that it likes to crash. @Notadouche is considering if the hormones are crashing once injected and I am considering it may be slightly crashed prior to injection. I feel a good thing to try is take one vial and add 8%bb, heat, filter and then see if the pip goes away. This should alleviate both of the concerns that have been brought forth. I have a sneaking suspicion this will help the pip considerably.

 

[Notadouche]

Agreeing with @Iron Vett on all accounts. If it were me doing quick math I’d add 3.2ml bb to that collective batch, heat, swirl and refilter into a new sterile vial. I’d also skip the baking in the oven step personally. That should yield a batch of 43.2ml @~230mg/ml ~17%bb and ba would be ever so slightly under 1% which is totally acceptable in my book.

 

[Ridethelightningbarefoot]

I believe the swirls are just fingerprints on the glass and the settling is just the uneven glass bottom but this reaction is wierd and painful so Im willing to try anything haha

 

[Cakedup]

I agree with ironvet. Although it is hard to tell in the pictures it does look like there's some hormone floating around in that bottle. Arre you using a magnetic hot plate with a stir Rod to mix the compound when Brewing?

I also agree with what the other guy said sorry I can't remember his name but I've never seen to see hold with less than 18% and even that this was Mig840. If it really held that that recipe I would be thinking I had Test E not Test C. I could be wrong but didn't you post about your Bold Cyp recipe and like I said I could be wrong so you should post it again but even that I thought was a little off as far as how much solvents used and it not crashing.

Bold cyp is always going to hurt especially if it's @ 200mg. That's why I personally will make it with regular EQ @ 200mg each and have no pip whatsoever. So you could always do the same or mix it in with your Test C, abd see it that helps..

 

[Notadouche]

@Cakedup makes a good point about suspecting your test cyp raws to be test E raws because your concentration shouldn’t hold I wouldn’t think as it is. Test e would however, easily. Test e raws always give me and a lot of others bad pip no matter how I brew it that’s why I’m test cyp til the day I die.

Where did your raws come from if you don’t mind me asking?