Test cyp recipes

[andrew brady]

Looking for good recipes for test cyp at 250grams/1000ml batch. I made it the other day & it crashed. My recipe was:
250g power
16ml BA
100ml BB

I'm new here & have seen posts for 20% BB & 1% BA

Help is appreciated.

 

[Meterman05]

It crashed because your BB was to low. At 10% cyp isn't going to hold. I would do the standard 2/20 for that and you should be fine. I have done cyp as high as 23%and been fine.

You can try to save your crashed batch by heating it up into a liquid again and adding more BB. You will have to adjust the math because you will no longer have 1000mL at 250mg/mL. Then filter your brew once again and it should be fine.

Next time just do 20mL BA and 200mL BB. Add your raws then fill up to the 1000mL line on your beaker to avoid using a displacement for the raw.

 

[andrew brady]

It crashed because your BB was to low. At 10% cyp isn't going to hold. I would do the standard 2/20 for that and you should be fine. I have done cyp as high as 23%and been fine.

You can try to save your crashed batch by heating it up into a liquid again and adding more BB. You will have to adjust the math because you will no longer have 1000mL at 250mg/mL. Then filter your brew once again and it should be fine.

Next time just do 20mL BA and 200mL BB. Add your raws then fill up to the 1000mL line on your beaker to avoid using a displacement for the raw.

How would u suggest I reheat up the crashed cup?
I've already bottle & capped it. Warm water perhaps??

 

[Meterman05]

How would u suggest I reheat up the crashed cup?
I've already bottle & capped it. Warm water perhaps??

If it's just in a couple of mother bottles you could wrap them in a heating pad on high for an hour or so. You could take a pot of boiling water and swirl it around. You can remove the caps and put them into an oven at 175-200 and check them after 20 minutes. I havealso done this but you can put it in a microwave for 10-20 second bursts. It depends on how bad it's crashed. If it's just starting to gel it shouldn't take much to get it to liquid pretty quick. If it's gone full on back into a wax it will take a bit longer.

If you have put them into vials then I would just tear all the seals off using some pliers and put them on a tray into the oven or microwave. It will be a pain in the ass to pour all of them out but better to get all that you can back into a large beaker. Alternatively if you were so inclined you can take a microwave safe dish fill it with water and heat it until boiling. Then take each individual vial and swirl it in the water until it's liquid again. Then with a syringe filter attached inject 1mL of filtered BB into each vial. With 1000mL of brew though it sounds like you will have 100 10mL vial sand that would be my last option.

Also in the future when you brew you can mix BB, BA, raw and carrier oil in a large beaker until you get your mix at the correct ratio. Cover it up and let it sit for a few days to make sure it holds then filter it. It sucks because you want to do all your brewing in one day but it beats having to empty out things and you can usually see crystals start forming if it's going to crash pretty quick.

 

[andrew brady]

I appreciate the help. I think I'm gonna warm it in the oven & add some BB to it like u said.
I APPRECIATE THE HELP BRO

 

[FR0Z3N_B0MB3RRR]

Pfizer makes his test cyp like this:

100mg/ml -> 1% BA 10% BB

200mg/ml -> 1% BA 20% BB

 

[Night_Owl]

200mg/ml -> 1% BA 20% BB

This is correct, 0.945% BA to be exact.
And 0.56 mL cottonseed oil per mL.

 

[Cumminstech]

What is the theory behind using less BB? Why don’t many recipes go above 20%? Why couldn’t you go 50% for example?

 

[MisterSuperGod]

What is the theory behind using less BB? Why don’t many recipes go above 20%? Why couldn’t you go 50% for example?

i would imagine because it's simply not necessary to go higher and would cause irritation in larger amounts.

 

[Cumminstech]

i would imagine because it's simply not necessary to go higher and would cause irritation in larger amounts.

What I’m really meaning to ask is if 20% is widely considered tolerable and much less likely to crash, why not just go to 20% out of the gate and not have to worry about crashing or anything?

And when guys scale it up from there they go to like 23% but don’t often see much over that... would something like 30% cause pip ?

 

[MisterSuperGod]

What I’m really meaning to ask is if 20% is widely considered tolerable and much less likely to crash, why not just go to 20% out of the gate and not have to worry about crashing or anything?

And when guys scale it up from there they go to like 23% but don’t often see much over that... would something like 30% cause pip ?

i believe most people that flirt with lower amounts are basically trying to reach the absolute minimum required.

Not just to reduce or eliminate PIP, but also to be injecting less chemicals over all. Being a solvent, i would think that higher than typical percentages would cause irritation and PIP.

 

[FR0Z3N_B0MB3RRR]

I even heard that too much BB could lead the solution to crash.. but who cares, standard recipes with standard concentrations are fine...
tryna reinventing the wheel it’s stupid for me...

 

[rasengan]

What is the theory behind using less BB? Why don’t many recipes go above 20%? Why couldn’t you go 50% for example?

What I’m really meaning to ask is if 20% is widely considered tolerable and much less likely to crash, why not just go to 20% out of the gate and not have to worry about crashing or anything?

And when guys scale it up from there they go to like 23% but don’t often see much over that... would something like 30% cause pip ?

Testosterone enanthate sold in Thailand by rotexmedica has 32.4% bb as carrier is castor oil.

 

[CApump]

The fact that you made a liter of gear with an unproven recipe is hilarious