test d instead of test e?

[whoremoan1]

probably a really dumb question

but ive ran out of test e raws and only have test d that i ordered by mistake

can i use the test d instead of test e brewed at 250mg and just pin the same days as test e

or will the ester build up too much giving me much more circulating test than test e would have?

 

[theotherguy]

probably a really dumb question

but ive ran out of test e raws and only have test d that i ordered by mistake

can i use the test d instead of test e brewed at 250mg and just pin the same days as test e

or will the ester build up too much giving me much more circulating test than test e would have?

If anything you'll have a little less hormone, but it'll likely be negligible to the point of not noticing a difference. The half life of decanoate is a bit longer than enanthate, so you could push your pins off to every 5-7 days instead of 3-5. But if you kept the same pinning frequency, it could be better if you have any sort of sides with test E at your current frequency.

 

[whoremoan1]

If anything you'll have a little less hormone, but it'll likely be negligible to the point of not noticing a difference. The half life of decanoate is a bit longer than enanthate, so you could push your pins off to every 5-7 days instead of 3-5. But if you kept the same pinning frequency, it could be better if you have any sort of sides with test E at your current frequency.

thanks

no sides at current pinning schedule 750 ew, MWF

so brewing up my test d 250mg and keeping everything the same with pinning and dosages wont change much in the grand scheme of things ?

 

[theotherguy]

thanks

no sides at current pinning schedule 750 ew, MWF

so brewing up my test d 250mg and keeping everything the same with pinning and dosages wont change much in the grand scheme of things ?

The amplitude of your peaks and valleys will be less drastic, which if anything I think would make you feel better due to more stable blood concentration. But otherwise no, there should be no difference, except it'll take a couple of weeks longer to clear your system when you're done blasting. Do you BNC or cycle off?

EDIT: If you are concerned with the volume of oil pinned, I think test D should be able to be brewed very easily at 300

 

[whoremoan1]

The amplitude of your peaks and valleys will be less drastic, which if anything I think would make you feel better due to more stable blood concentration. But otherwise no, there should be no difference, except it'll take a couple of weeks longer to clear your system when you're done blasting. Do you BNC or cycle off?

great! and yes BNC thanks for the solid info !

 

[theotherguy]

There is no option for MWF on this plotter, so I just said EOD, but this is roughly what the transition would look like and the hormone concentration in your blood would be, relative to each compound. The first 10 weeks is test E and the next 10 weeks is test d

 

[whoremoan1]

There is no option for MWF on this plotter, so I just said EOD, but this is roughly what the transition would look like and the hormone concentration in your blood would be, relative to each compound. The first 10 weeks is test E and the next 10 weeks is test d

View attachment 162701

do you think i should brew the test d at 300mg?
then it would be nearly identical to test e at 250mg?

 

[theotherguy]

do you think i should brew the test d at 300mg?
then it would be nearly identical to test e at 250mg?

What I meant was if you want to inject slightly less oil for injecting 250mg MWF, then brew it at 300. Instead of pinning 1mL to hit 250 mg, you would pin .85 mL (if brewed at 300 mg/mL) to hit 250 mg. Otherwise you can brew it at 250 and be just fine.

But, based on ester weight, you would need to inject about 850mg/wk of test D in order to have an equivalent amount of test as test E @ 750 mg/wk. So if you brew it at 280mg/mL, and just pin 1mL on MWF, you should have pretty close to the same test. Or brew it at 300 and pin .9-.95mL MWF. Or brew it at 250 and pin 1.1mL MWF. It's all personal preference at this point, and you may be splitting hairs that don't matter :shrug:

 

[whoremoan1]

What I meant was if you want to inject slightly less oil for injecting 250mg MWF, then brew it at 300. Instead of pinning 1mL to hit 250 mg, you would pin .85 mL (if brewed at 300 mg/mL) to hit 250 mg. Otherwise you can brew it at 250 and be just fine.

But, based on ester weight, you would need to inject about 850mg/wk of test D in order to have an equivalent amount of test as test E @ 750 mg/wk. So if you brew it at 280mg/mL, and just pin 1mL on MWF, you should have pretty close to the same test. Or brew it at 300 and pin .9-.95mL MWF. Or brew it at 250 and pin 1.1mL MWF. It's all personal preference at this point, and you may be splitting hairs that don't matter :shrug:

your a legend
thank you

 

[klokke23]

There is no option for MWF on this plotter, so I just said EOD, but this is roughly what the transition would look like and the hormone concentration in your blood would be, relative to each compound. The first 10 weeks is test E and the next 10 weeks is test d

View attachment 162701

You can but it requires more work.