Test-E first brew

[charliewaqs]

Long time lurker on this forum and wanted to start being a contributing member.

I’ve just made my first batch of Test-E at 250mg/ml. It’s for personal use.

2% BA / 13% BB / MCT oil.

As I already have UGL supply to get through first, I will be storing this for at least 6-12 months. Was hoping for some feedback on how it looks!

Thanks

 

[rasengan]

is it cloudy ? or just looking cloudy in picture ?

 

[charliewaqs]

Here’s another pic

 

[Carter79]

Here’s another pic

View attachment 132965

Pretty simple way to answer if its cloudy looks fine to me but did you use a water bath to heat it? Or what was your heating method

 

[charliewaqs]

Pretty simple way to answer if its cloudy looks fine to me but did you use a water bath to heat it? Or what was your heating method

I used to a magnetic stirrer with hot plate! All the mixture was in a beaker and I placed that on the hot plate and let it stir under small amount of heat for about 30-40 mins.

Doesn’t look cloudy to me at all.

 

[rasengan]

Here’s another pic

View attachment 132965

thats nice looking clear test e let us know if you experience pip . i made tren/mast blend in mct oil using 20% eo and its thin smooth and painless . where did you purchased test e from ? purple panda ?

 

[Carter79]

I used to a magnetic stirrer with hot plate! All the mixture was in a beaker and I placed that on the hot plate and let it stir under small amount of heat for about 30-40 mins.

Doesn’t look cloudy to me at all.

Ya looks clear to me as well just wanted to make sure that you didn't introduce water some how as the other guy was worried! Looks good to me though good job.

 

[Clamslaps]

I used to a magnetic stirrer with hot plate! All the mixture was in a beaker and I placed that on the hot plate and let it stir under small amount of heat for about 30-40 mins.

Doesn’t look cloudy to me at all.

It looks fine. I am too poor/lazy for the magnetic stirrer or hot plate, but I'm jelly you've got them.

Next time toy with bumping the BB and raising the dosage

 

[charliewaqs]

Thanks for feedback everyone. Defo no water introduced. And all got filtered through a 0.22 straight into the vials.

My first attempt so quite pleased. Will definitely try something different next time!

 

[Clamslaps]

Thanks for feedback everyone. Defo no water introduced. And all got filtered through a 0.22 straight into the vials.

My first attempt so quite pleased. Will definitely try something different next time!

First time is the hardest, you wonder if you fucked something up, you spend lile 6 hours getting it right, you wait like 4 weeks to pin it, telling yourself you need to wait for the BA to kill the germs you might have missed or see if there's any condensation.

 

[CApump]

It looks fine. I am too poor/lazy for the magnetic stirrer or hot plate, but I'm jelly you've got them.

Next time toy with bumping the BB and raising the dosage

Next time he can actually LOWER the BB and raise the dose and have a great finished product

Looks good op, nice job!

 

[SubAlitt]

Did you try it ?

What about PIP?

 

[charliewaqs]

Will report back at another time. Currently cutting

 

[charliewaqs]

Did you try it ?

What about PIP?

Currently on cruise. Pinned into glutes and thighs a few times so far. Only got PIP once on first attempt in right thigh which is nothing unusual.

Very happy so far. Goes in so smooth!

 

[charliewaqs]

Some more goodies for upcoming cycles [emoji854]

 

[Christop G]

Looks good, You upped the mg of test e did you keep ba bb ratio the same?

 

[Champ1988]

I'm about to get a magnetic stirrer/hot plate. What kind of settings/temp did you set it at?