Test e question

[ickyrica]

Take it easy on me guys, first time brewing here!! My question is about the finished oil. It is so clean and clear looking, I love it lol. When I shake the vial I can see swirls in the oil. The swirls go away rather quickly and it is crystal clear, but I see them when i shake the vial non the less. I can't remember seeing this in the cyp that I ran but I can't remember paying attention either.

I pinned it and it was painless. It loads into the gear just fine as well. I used 1%ba, 10%BB and gso. Filtered w autofoxx, slow and steady there.

Is this normal/ok? The swirls specifically is what I am questioning. Thanks for reading guys!

 

[Docd187123]

Yes it's fine

 

[ickyrica]

Thanks man, I appreciate the answer. After the filtering process I couldn't imagine it being a bad thing, just had no clue. Hopefully the raws turn out to be good potency

 

[XKawN]

What was your mg to ml ratio?

 

[ickyrica]

I used 300mg/ml. Expecting it to be closer to 250mg/ml. I'm fearfull of underdosed product.

 

[Big_paul]

I pinned it and it was painless. It loads into the gear just fine as well. I used 1%ba, 10%BB and gso. Filtered w autofoxx, slow and steady there.

I don't see how you could go wrong with the amount of solvents you have used if brewing test e even at 300mg/ml.

 

[Docd187123]

Take it easy on me guys, first time brewing here!! My question is about the finished oil. It is so clean and clear looking, I love it lol. When I shake the vial I can see swirls in the oil. The swirls go away rather quickly and it is crystal clear, but I see them when i shake the vial non the less. I can't remember seeing this in the cyp that I ran but I can't remember paying attention either.

I pinned it and it was painless. It loads into the gear just fine as well. I used 1%ba, 10%BB and gso. Filtered w autofoxx, slow and steady there.

Is this normal/ok? The swirls specifically is what I am questioning. Thanks for reading guys!

What were the exact amounts of everything you used? BA, BB, raw powder, and carrier oil?

 

[ickyrica]

I don't see how you could go wrong with the amount of solvents you have used if brewing test e even at 300mg/ml.

That's good to hear brother.

What were the exact amounts of everything you used? BA, BB, raw powder, and carrier oil?

BB 15ml
BA 1.5ml
GSO 90ml
45g test e

 

[ickyrica]

Pre sterilized vials as well...

 

[Docd187123]

That's good to hear brother.


BB 15ml
BA 1.5ml
GSO 90ml
45g test e

The recipe is pretty close. You'll be fine.

 

[ickyrica]

I figured I would be but the swirls it makes when shaken had me questioning things. Someone posted a pic recently in the media section of tren, it has the same type of look.

The recipe is pretty close. You'll be fine.

 

[T_verde77]

I usually keep bb at 20%. As long as it holds its fine. just stick with the good recipes online and never use too much bb or ba

 

[Geterdun]

Looks like liqueur legs. I've seen it a lot in my gear. I don't homebrew, but I do see it. I think I don't in PROP.

 

[XKawN]

333.3333333mg/ml
1% ba
10%bb

Maybe a little low on the bb at that % active ingredient.

 

[ickyrica]

Yeah, I didn't want to go

333.3333333mg/ml
1% ba
10%bb

Maybe a little low on the bb at that % active ingredient.

I can adjust with more. I was actually told 18% but the test dissolved easily. What's the risk if it's low? More pip I'm assuming?

 

[XKawN]

Yeah, I didn't want to go

I can adjust with more. I was actually told 18% but the test dissolved easily. What's the risk if it's low? More pip I'm assuming?

Well, imo it may have not completely held in solution. May get a bit of pip, but it's test e so I doubt it will be unbearable. Have you capped everything yet?

 

[ickyrica]

Well, imo it may have not completely held in solution. May get a bit of pip, but it's test e so I doubt it will be unbearable. Have you capped everything yet?

It's all filtered and bottled. I have a few 50ml vials at this point. I am not having any issues with injections so maybe I'm good? If it becomes an issue could I always add more with a syringe and filter, no?

 

[XKawN]

It's all filtered and bottled. I have a few 50ml vials at this point. I am not having any issues with injections so maybe I'm good? If it becomes an issue could I always add more with a syringe and filter, no?

Shit, if you ain't having any pip issues then g2g. If there were a problem you could add a bit more bb. A bit of work so unless it's necessary I wouldn't bother.

 

[ickyrica]

Thanks for the replies fellas. I am considering my first batch a win I guess.

I had a vial of test e from a friend and after one use I had a big lump on my buttcheek. It just hurt wicked bad and after consulting a trusted member here it turned out that it was a sterile absess. Tossed that shit in the garbage asap.

I was sitting on some raws and this made me feel like I should just make my own from now on, unless its difficult or a specialty or something of the like. this is almost painless, nothing bad in any way thankfully. Now that I know those "liquor legs" that it can get when shaken is normal I am confident that it's g2g.

 

[Kinikuman]

I usually keep bb at 20%. As long as it holds its fine. just stick with the good recipes online and never use too much bb or ba

Very true. The biggest causes of problems and PIP come from too much of something: too high a concentration, or too much BA/BB. My rule of thumb is to keep concentrations at or near normal pharma levels (Ex: Test E =250mg/ml +/-, Test C =200mg/ml +/-, etc.). Just because you can get something to hold doesn't mean that you've achieved the ideal concentration. Believe me, no one on this board knows more about brewing AAS or has more real, rigid scientific data backing up their processes than the pharma companies that developed the stuff and brought it to market. They have VERY GOOD reasons why they chose the particular formulations and concentrations they did. Because they were IDEAL to vast majority of the using population.
I have personally experienced flubs with too high a concentration (crashing, nasty PIP), and too much BA (stung like hell and more nasty PIP). In the realm of AAS users more is better tends to be the norm but when brewing I feel this can be a major mistake. Pinning more oil never hurt anybody IME.