Tren Brewing, The same issues and New brew with no issues

Hi guys, had the same common problem with tren ace,But today it seems tren ace + tren e goes perfectly.

Had to make some clarifications:

1st Brew made this year was 50% from a source (And it was the second half of the whole because the first it was brewed last year with no problems,it wasnt muddy etc it gave me cough night sweats etc, and it was just Tren Ace brewed at 100mg ml with 1% BA 20% BB) and the other 50% was from PPL.

It was a total mess, it was muddy as fuck and it brought brown rocks as precipitates, i filtered and pinned and it gave me absolutely nothing effect, libido, cough, night sweats, strenght, no nothing. And i have to point out that i used a lot of warm, because at the time i tought i did brew correctly but i was doing only mistakes. I putted the becker with BA BB of that hybrid sourced tren ace into the flames of burner, made solubilize, broke the hormone for sure than added GSO and had a slime with crashed hormone and dark orange brown rock shaped precipitates. As stated i pinned it after filtration and got nothing effect from it.

bought from PPL some tren A and some tren E, i read about the 0.5g of Tren E to being added to 100ml of Tren A (maybe brewed at 100mg ml) etc, but wanted to try another thing.

I just tried 250mg of Tren A with 500mg of Tren E, to make 75mg ml (25 Tren A + 50mg Tren E / ml) , used 25% BB, made solubilize on the magnetic stirrer at 60 Celsius degrees until it came clear and light yellow, let it cool and then added MCT.

stirred at 50 C for some minutes (with near to maximum stirring speed) and obtained a pretty yellow clear mix.

It was just a trial, and it seems to have gone very well.

i don t know when i ll filter it and when i ll use to give you feedback, but right now i m pretty happy about it, because i did fear tren brew would have been a total nightmare again.

i have to thanks @ickyrica because some times ago he opened my eyes about brewing, i wrote in a post about the fact i knew someone should have used hotplate stirrer but i didnt have and tought it was ok to put the hormone in a becker onto the burner flames just for the time need to sobulize, but I didn’t even know how much heat i putted into my hormone, he told i was doing everything bad.
Then i studied the Homebrewing section, bought a magnetic stirrer hot plate, read 30pages of topics in 3 Weeks and tried today.
And with the fear that heat can destroy the hormone (since i trashed near to 700$ of tren)
I wont go over 60 Celsius degrees anymore,
And since i didnt have problem with BB i ll maintain low classic concentrations.

in the pic you can see the color and the clearness, its totally liquid like the MCT
 
Yea too much heat it will cloud every time.
test e I got it way hot on a batch 95c on accident and oddly even it was incredibly potent but with in a month went cloudy. Not sure why but that’s what happened
 
Just a thought, many alcohols have quite a low bp and are quite volatile so the likelihood of alcohol evaporating in high heat would be pretty good I think.
I usually don't add my BA until the mix is essentially back to room temp. Last thing before I filter and bottle.
 
Tren doesn't need any heat to be made. None. I've never once turned my hotplate on to make it... I've made it without a magnetic stirrer too but it does make it easier/faster to have.

Put raws in a beaker, pour all the BB over them. Let sit for 20min. Turn on magnetic stirrer, let it run until they're dissolved. Add all the MCT and continue to stir. Add the BA a min or so before you turn off the magnet and you're done. Filter, vial, pin, bam.
 
If i don't have tren e, Is it possible to add mast e for example?
Don’t know... if you have tren ace , brew it as soon as you receive it...

That story of adding tren e has been suggested by Panda because some batches of tren ace had unesterified tren on them... and the more time passes after batch is made, the more problems you could encounter on brewing it...
 
Don’t know... if you have tren ace , brew it as soon as you receive it...

That story of adding tren e has been suggested by Panda because some batches of tren ace had unesterified tren on them... and the more time passes after batch is made, the more problems you could encounter on brewing it...
Yeah i follow up the story from before but was wondering if the actual hormone is important or just any hormone with enan ester.
 
Tren doesn't need any heat to be made. None. I've never once turned my hotplate on to make it... I've made it without a magnetic stirrer too but it does make it easier/faster to have.

Put raws in a beaker, pour all the BB over them. Let sit for 20min. Turn on magnetic stirrer, let it run until they're dissolved. Add all the MCT and continue to stir. Add the BA a min or so before you turn off the magnet and you're done. Filter, vial, pin, bam.
Can you recommend a specific magnetic stirrer? Just want to make sure I get the right one the first time. It would be for small brews, like 10-20g in raws at a time. Txs.
 
Can you recommend a specific magnetic stirrer? Just want to make sure I get the right one the first time. It would be for small brews, like 10-20g in raws at a time. Txs.

I have an anzeser but I don't know if there's really a wrong one you could get... Mine is a combination hot plate and stirrer, I'd definitely recommend getting one of those. They're all pretty close to being the same. It doesn't need to be real advanced... At most, I just warm the oils for 95% of the compounds I make. The only ones that do need real heat are esterless raws.
 
I have an anzeser but I don't know if there's really a wrong one you could get... Mine is a combination hot plate and stirrer, I'd definitely recommend getting one of those. They're all pretty close to being the same. It doesn't need to be real advanced... At most, I just warm the oils for 95% of the compounds I make. The only ones that do need real heat are esterless raws.
Cool....thanks. I'll be doing tren ace first so would you recommend no heat to be the safest method of not fucking up?
 
Cool....thanks. I'll be doing tren ace first so would you recommend no heat to be the safest method of not fucking up?

Yes, I would not use any heat at all... Tren is heat sensitive + heat not needed to brew it = don't use heat.

You can make it without the stir magnet, just put the BB and raws in a beaker and let it sit covered overnight. You may need to add a little bit or all of the oil for this method though, but it'll come together. That was how I made it my first time.
 
Back
Top