MESO-Rx
Anabolic Steroids
Tren E 250mg
- Thread starter Vfljuicer
- Start date
Iron Frenchie
Member
It should be fine with 20% BB. But I would do 10% BB and 10% EO.
I actually am doing all eo as my carrier...I know many people would disagree with doing that but I have no bad reaction to eo and it makes for a much thinner oil to pass through smaller gauge pins much easier. I prefer 100% eo as to any other carrier.
Iron Frenchie
Member
With 100% EO no need for BB.
I rather it be 250mg but if it would be an issue of possibly crashing then I’ll go with 200mg that’s the reason I ask this question. I know 200 will work perfectly with carriers like gso mtc oils and so on. Usually with eo being your carrier you can obtain a higher mg of product and still hold. I just don’t want to try it at 250mg if nobody else has ever had success since it’s such an expensive compound. However if it can be done at 250mg that’s what mg I would like to go with. Just my preference. Nothing wrong with 200 but I feel 250 is very possible with eo being your carrier. I have been wrong before that’s why I ask the question instead of taking the risk. I realize the reason behind not seeing tren enanthate doses higher than 200mg but most labs do not use eo as their carrier. I feel life would be easier with 250mg. Thanks for your input though.
Also the best tren I have ever used was a top brand lab back in 2005-2012 A.P I’m sure most can guess the brand. It was dosed at 250mg per ml...they have thin oil products so my guess was they probably use eo as a carrier too. So it does hold at 250mg just not sure what they used as far as carrier and bb. I’ve seen ugl labs with 300mg one which I used and it left some serious pip but the A.P brand had no pip at all and was a very trusted brand that also had a website to check your gear making sure it wasn’t faked. They are still around but I’ve heard the brand has switched hands since then. Hands down best tren I’ve used so I know it’s possible.
Holidaypay
Member
U can try at 250 let it sit for a day an if it doesn't hold u can just add more oil to dilute it to 200 use the steroid cal to figure out the diff for example
15% bb of 100ml=×
15%bb of 120 ml=y
Y-x= what u need to add
Same thing for ba
That’s what I’ll do. Thanks
Holidaypay
Member
Np should hold with 100% eo imo
Understandable , but is the 50mg worth the risk ?
Tren isn't the most expensive but it definitely isn't cheap.
You can just always add .25 cc to your syringe to make up the difference
That’s common sense man and not the question I asked. Your reply has no value.
Avatar1338
New Member
Ive managed to make a painless tren e 300 but wont post the recipe. Went through a good amount of raw powder until i had this recipe. What i will tell you is that 250 should be ok with 20bb 1 ba using eo as main carrier.
The whole point of forums like this is simply helping one another with goals etc...
The fact that you won't tell people the recipe is pretty childish bro.
Anything knowledge I have I will gladly help someone
And I have learned alot from other members and they had no problem linking me to something or sharing their methods or secrets.
I don't expect anything productive to come from your next response but what you are doing defeats the purpose of why you're even here.
Avatar1338
New Member
you asked for 250 and i told you how to make 250mg/ml. i gave you my advise. because you asked for it. i have invested my time and quite some money in the 300 recipe therefore i wont post it openly. whats childish about that? i find it a real cheek that you demand my recipe and calling me childish. i would have been willing to give you more tips or point you in the right direction if you would have asked me nicely.
Juicemonkey72
New Member
I’ve never made tren e and am making it for the first time today or tomorrow. It will be 200mg. Will 15%bb 1% ba hold in mct. Thanks for any help you can give. ✌
I’ve made it 1/18 and it held fine
Juicemonkey72
New Member
That’s what I decided to brew it at after some reading. Thanks for your reply. ✌
Avatar1338
New Member
i personally would use a mix of castor oil and eo. this combination can hold the most mg/ml and will ensure a slow release. mct isnt ideal for long esters because it will be absorbed much faster. this would cause a quicker release and would change the pharmacokinetics of the drug (esp. with long acting esterfications like enanthate/ cypionate/ decanoate/ undecanoate or undecylenate).
