Benny
New Member
anyone know how high a concentration you can brew with EQ? Is 300mg/ml possible with out EO? At what point does pip start coming in to play? Thanks for any input.
MESO-Rx
Anabolic Steroids
Highest EQ concentration?
- Thread starter Benny
- Start date
nophat
Subscriber
EQ has no pop up to 350
For me anyway
I stick to the standered 250 mg
Unless someone wants higher concentrations
For me anyway
I stick to the standered 250 mg
Unless someone wants higher concentrations
nophat
Subscriber
Pip up to not Pop
Never work with EQ personally but from what I've gathered it's already a liquid at room temp so getting it to hold should be easy without EO and minimal BA/BB. The higher the concentration the more it'll have a honey like consistency so it's a tradeoff. 300mg/ml might be possible without any solvents period but it's probably better to use them to keep the oil thinner.
Benny
New Member
Thanks, I am thinking I may try 300mg/ml, using 2% BA and either 20% or 18% BB. That concentration makes my pinning schedule work out well for up coming cycle.
nophat
Subscriber
You don't need that much BB
I would drop it to 8-10%
Like doc said EQ is or can be messy.
Had a fella send me what he was told was testE
When I recieved it it looked like EQ so I'm thinking it is.
Never seen testE come in liquid form.
We are on the topic not high jacking your thread.
Doc or any one have ever seen this.
Or is my asumtionrite.
I would drop it to 8-10%
Like doc said EQ is or can be messy.
Had a fella send me what he was told was testE
When I recieved it it looked like EQ so I'm thinking it is.
Never seen testE come in liquid form.
We are on the topic not high jacking your thread.
Doc or any one have ever seen this.
Or is my asumtionrite.
333.33, 400, and 450 is where I begin to max out. 400 and up can be very slow to draw up and inject, can add more bb if it's an issue for you.
Nophat - throw the eq in the freezer - if it's a stiffer liquid, it's eq. If it solidifies it may be test e
(Don't leave it in long enough to drop too far below freezing, maybe an hour tops)
(Don't leave it in long enough to drop too far below freezing, maybe an hour tops)
Test e would be liquid if the temps got hot enough. Forget it's melting point but guessing it's around 100deg. I got my raws in winter and even then the test e was a little "damp" I guess you could say
nophat
Subscriber
Ya shit was odd
I had my test E out with it
Same temp
And stayed powder form.
Even had that EQ smell not strong but a little.
And sticky as hell
EQ can be a mess I don't personally use EQ tryed it for a few months worked well but it's not for me.
I stay lean 24/7 so I try to stick with bulking gear.
I had my test E out with it
Same temp
And stayed powder form.
Even had that EQ smell not strong but a little.
And sticky as hell
EQ can be a mess I don't personally use EQ tryed it for a few months worked well but it's not for me.
I stay lean 24/7 so I try to stick with bulking gear.
hotdog23
New Member
I will be using a 400ml/recipe @ 2BA 10BB, prob only need the BA but better safe than sorry.
There was a thread on here about 500/ml EQ with only 5% BA... Sounds like a bad idea
There was a thread on here about 500/ml EQ with only 5% BA... Sounds like a bad idea
Why not go 1% BA as that's all that's really needed and bc BB is a better solvent than BA. So lower BA and maybe up the BB another 2-3%?
Benny
New Member
Decided on 300, used 2% BA and 10% BB
hotdog23
New Member
If you think 1% BA is all that's needed for bacteriostatic solution I'll roll with that n 15% BB
I used 1% in all my brews and I believe the pharmacy uses .9%. If you look at the back of a bad water vial it says .9% BA.
hotdog23
New Member
yes it does
When S*CS was still testing AAS for us I sent a 500mg/ml EQ. Came back 494mg/ml, that was beautiful! Wish I would have kept that test. It would go through a 25g 5/8 smoothly, take a little longer but no PIP. If I recall correctly my guy did it using 1/20 BA/BB.
6Fingers-Pharma
New Member
BA over 1% is purely for psychological needs. BB 8-10% is typical and IMO will be preferred by most. Since EQ is liquid at room temperature, there is theoretically no way to crash from solution, absolving any need for further solvents. Sounds great, but what kind gauge will be required to move something so thick?
At this point, it is merely a dilution to thin the media to a point of comfort, which is completely subjective.
Keep in mind that physical pain is only one factor to consider. Higher concentrations have a higher rate of muscular disruption. Whether or not it is greater than an extra pin, who can say?
At this point, it is merely a dilution to thin the media to a point of comfort, which is completely subjective.
Keep in mind that physical pain is only one factor to consider. Higher concentrations have a higher rate of muscular disruption. Whether or not it is greater than an extra pin, who can say?
Does anyone have anything we could reference max concentrations for all AAS? I'm particularly interested in NPP at the moment. And Test prop 
Rjs725
New Member
I got EQ dosed at 500mg/ml from my source. It is extremely thick and draws up slow in a 21g. I will have to take a look at the BA/BB ratio when I get home, but it is brewed in GSO.
