Brewing painless gear

[mjf]

Ok. So I did a minimal amount of reading and decided to start brewing my own gear. I saw some recipes and know where to find the calculator for amounts of everything to make this happen. At least I think. I may be oversimplifying this, but it seems fairly easy.

The powders I purchased are test prop, npp, tren ace. I haven't purchased the carrier oil, ba, bb, filters, etc. I was thinking gso for my carrier and simce I'm new and trying for the first time, i should go ahead and struggle with .22 whatman syringe filters rather than buying alot of expensive equipment.

I've seen many recommendations for a basic 2% ba, 20% bb, but have also read 1% ba and much lower bb will work for what I'm brewing. 1% seems like the lowest you can go, but what causes the pip I'm experiencing frim my ugl short ester gear? Is it the ba, bb or both in a high concentration "just to be safe?" What percentage bb would be good?

 

[kap73]

I use MCT oil, my prop, npp, are pretty much pip free. 20% BB 2% BA

But it comes down raws aswell, they may be dirty which will massivly contribute to PIP

 

[jeffspacht]

20% BB 2% BA is good, i always use this. if you want painless gear, the carrier oil EO is a best choice

 

[jeffspacht]

you also can try half grape seed oil and half EO, the effect is amazing !

 

[jeffspacht]

you also can try half grape seed oil and half EO, the effect is amazing !

 

[mjf]

EO it seems some people have a bad reaction to. Plus it deteriorates some rubber products such as bottle stoppers and syringe rubber.

 

[jeffspacht]

EO it seems some people have a bad reaction to. Plus it deteriorates some rubber products such as bottle stoppers and syringe rubber.

yes, that is why most people use grape seed oil

 

[XKawN]

EO it seems some people have a bad reaction to. Plus it deteriorates some rubber products such as bottle stoppers and syringe rubber.

I'd say more people have bad reactions to mct oil than eo. Hard to say why your getting pip from your source. Many factors involved. If you want more of a sure thing go GSO and a simple ratio of 1% ba and 18% bb. Either way just brew in small amounts in the beginning. I've seen people brew Thier whole order of raws in one sitting and fuck up.

 

[Jakan]

The best way to painless oils is
- lower concentration
- BB max 15-20%
- BA 1%
- if you dont have reaction to EO - 10-20% EO

 

[bonacris]

K.I.S.S
Keep it simple stupid. Use the given formulas. 2% or 1% BA is such a small amount it won't cause any pip. I do the very basics but do them right, no high concentrated gear etc and it'll be painless

 

[mjf]

I wanted to try the eo, but just read a few things that changed my mind.

 

[XKawN]

I wanted to try the eo, but just read a few things that changed my mind.

Share. What did you read and where?

 

[mjf]

Just about allergic reactions or bad reactions in general and it's tendency to eat up certain rubber products. No specific place for that info, just from reading threads here and there.

 

[Docd187123]

I believe Dr. Jim posted recently how EO is not FDA approved. You'll only find it being used in compounding pharmacies and not in pharmaceutical companies.

 

[mghoward74]

Ok. So I did a minimal amount of reading and decided to start brewing my own gear. I saw some recipes and know where to find the calculator for amounts of everything to make this happen. At least I think. I may be oversimplifying this, but it seems fairly easy.

The powders I purchased are test prop, npp, tren ace. I haven't purchased the carrier oil, ba, bb, filters, etc. I was thinking gso for my carrier and simce I'm new and trying for the first time, i should go ahead and struggle with .22 whatman syringe filters rather than buying alot of expensive equipment.

I've seen many recommendations for a basic 2% ba, 20% bb, but have also read 1% ba and much lower bb will work for what I'm brewing. 1% seems like the lowest you can go, but what causes the pip I'm experiencing frim my ugl short ester gear? Is it the ba, bb or both in a high concentration "just to be safe?" What percentage bb would be good?

You did minimal amount of reading and research before you decided on brewing your own gear, meanwhile purchasing Test p, tren a, and npp?

Sounds like a good way to start off, I guess...

This is exactly why it's so hard for me to help people.....,but I really do want to help.

 

[mjf]

I was being facetious, somewhat. I've been reading and thinking about this for months now. I know where to go for brewing techniques, recipes, etc I just haven't committed it to memory or done it before to know some of the specifics.

I'm of course no expert, but I know enough to get it done and not die from my own brew.

 

[Big_paul]

Ok. So I did a minimal amount of reading and decided to start brewing my own gear. I saw some recipes and know where to find the calculator for amounts of everything to make this happen. At least I think. I may be oversimplifying this, but it seems fairly easy.

The powders I purchased are test prop, npp, tren ace. I haven't purchased the carrier oil, ba, bb, filters, etc. I was thinking gso for my carrier and simce I'm new and trying for the first time, i should go ahead and struggle with .22 whatman syringe filters rather than buying alot of expensive equipment.

I've seen many recommendations for a basic 2% ba, 20% bb, but have also read 1% ba and much lower bb will work for what I'm brewing. 1% seems like the lowest you can go, but what causes the pip I'm experiencing frim my ugl short ester gear? Is it the ba, bb or both in a high concentration "just to be safe?" What percentage bb would be good?

You can use the same method to brew any compound.
1 add raw to a beacker, and slowly add bb until all the raw has been dissolved.For the gear you are brewing it will be 15-20 % For difficult esters to disolve like the ones yo are using, you can use low heat to help. Just let it cool to room temp to see if it stays in solution.
2 add your carrier and ba. If you will be storing it or using a larger vial than 10ml, you can add 2-3% ba, otherwise I would use 1% ba. The reason you would use more for a 20ml than a 10ml is because you will be drawing from the vial more, and there is an increased likelihood that it could become contaminated.
3 using 22.5 filter, filter sterile gear into sterile resealed vials.

PM if you need any help or run into any problems.

 

[Big_paul]

Don't make crazy high concentrations. 100mg/ml is good for what you are doing. It will not cause any pip if you do it right.

 

[Big_paul]

DONT use heat to dissolve tren a. The other 2 you can.

 

[Wunderpus]

DONT use heat to dissolve tren a. The other 2 you can.

Oxidation?