Tren Gone Cloudy 1h After Filtering

[Wunderpus]

Just brewed a batch made from tren pellets following the directions. The bottom has crystals, that when shook, it clouds the mixture. Could have been caused by too much heat, so it cystalized. I just tried injecting .5, as is, to see what happens. I can always let it all settle, withdraw the clear, and put into another bottle to use.

It's crashed. What % BA and BB did you use? DO NOT inject it until we fix this.

 

[nophat]

To be honest the cloudy sounds like either impurities or the oil. I have made it with GSO and it was cloudy, I ran it through the filtration again and it cleared up, several days later it started to cloud up again, that tells me its degradation in the light carrier oils and I rarely use more than 3% total BB/BA with my tren if under 20mls.
Pure tren is a great substance to work with and easy. I did a search of the cloudy and it appears that hexamine used in the process could be reacting with the BB and breaking down the chemical component. This is no big deal since the amounts are minimal. It will form a cloudy precipitation that will not affect the tren itself but could cause site irritation and scar tissue development where injections occur.
I will ask my friend who is currently doing the manufacturing process and see what he says. I will post his reply here
Not my info;From a post i came across.

I dident post this.
Wtf! I never right that much in a post.

 

[XKawN]

I dident post this.
Wtf! I never right that much in a post.

Lol, sometimes i do when I'm drunk. Takes me forever then i proof read it and say "why did i even type this" and i delete it before posting it.

 

[Wunderpus]

I dident post this.
Wtf! I never right that much in a post.

This is definitely not in NoPhat speak, that's for sure!

 

[SheriLee]

It's crashed. What % BA and BB did you use? DO NOT inject it until we fix this.

It's crashed. What % BA and BB did you use? DO NOT inject it until we fix this.

That was my first mix, I think I can do better next and just take my time.

• .8mL BA (Gives 2% overall volume)
• 7.2mL BB

I did let it sit again in light boiling water and then put in toaster oven at 200 degrees for 10 minutes. The crystals are now gone, the solution is amber clear. A white film remains on parts of the walls of the vial, but it doesn't seem to mix with the solution.

The .5 cc injections every other to every 2 are good. I feel no pain from the injection. I feel a little sore in the spot for a couple of days then massage the area. No abscess. I feel it's as sterile as it will get.

 

[shredded]

Try this it has worked for me every time add either 25% test prop or Tren enanthate, now i don't know why this works but every time my tren Ace has gone cloudy if i add either of these compounds it clears and stays clear.
If your worried about wasting a lot of gear just make a 10ml sample and watch how either of these compounds will turn cloudy tren clear and keep it clear. This will only help with the white milky cloudy substance that tren can sometimes have, if your getting crystals then thats another matter all together.

 

[Skull]

Lol I can't find the thread to copy it an bring it to your newly created one soooo....guess I'll just have to tag ya in it @ironwill1951 ^^^^

 

[Big_paul]

Try this it has worked for me every time add either 25% test prop or Tren enanthate, now i don't know why this works but every time my tren Ace has gone cloudy if i add either of these compounds it clears and stays clear.
If your worried about wasting a lot of gear just make a 10ml sample and watch how either of these compounds will turn cloudy tren clear and keep it clear. This will only help with the white milky cloudy substance that tren can sometimes have, if your getting crystals then thats another matter all together.

I'm going to keep on telling you guys that if you dissolve your raw first all you have to do is add your carrier up to the volume and dosage you desire. This shit is so easy a 5 year old could do it.

 

[shredded]

I'm going to keep on telling you guys that if you dissolve your raw first all you have to do is add your carrier up to the volume and dosage you desire. This shit is so easy a 5 year old could do it.

Always add the raw first then the solvents and then the carrier, in my case always MCT, use a heated magnetic stirrer and it will still go cloudy sometimes it filters clear and will deposit some milky like substance on the bottom, anyway im not going to have a pissing match with you everyone i told to add Test P or Tren E about 25% has always had go clear and stay clear, good luck with your 5 year old making your gear.

 

[Big_paul]

I share what works for me. Take it or leave it. No problem here.

Always add the raw first then the solvents and then the carrier, in my case always MCT, use a heated magnetic stirrer and it will still go cloudy sometimes it filters clear and will deposit some milky like substance on the bottom, anyway im not going to have a pissing match with you everyone i told to add Test P or Tren E about 25% has always had go clear and stay clear, good luck with your 5 year old making your gear.

 

[Cownan]

guicol brother. 2.5%. Do that and tren will have a better chance of being clear. Ive had cloudy tren before and it was awesome. Just cause its cloudy means nothing. Nor does it need that woody smell. All cloudy means is that the solvents cant hold all the raw so it floats around. If you heat it up before shots itll go clear and then you can shake, pull and shoot. Ive never had a problem as long as you make it yourself or trust the lab you get it form

 

[Big_paul]

Always add the raw first then the solvents and then the carrier, in my case always MCT, use a heated magnetic stirrer and it will still go cloudy sometimes it filters clear and will deposit some milky like substance on the bottom, anyway im not going to have a pissing match with you everyone i told to add Test P or Tren E about 25% has always had go clear and stay clear, good luck with your 5 year old making your gear.

The 5 year old has it figured out like a,b,c. Let us use a monkey next. I don't even understand what you are saying. This post is incoherent.

 

[Cownan]

The 5 year old has it figured out like a,b,c. Let us use a monkey next. I don't even understand what you are saying. This post is incoherent.

I agree. If you add raw first, especially to heat tren will melt and stick to the glass. It doesnt matter what order you add solvents or oils. All the same in the end. But hey, Im only 4

 

[Cajun897]

I'm going to keep on telling you guys that if you dissolve your raw first all you have to do is add your carrier up to the volume and dosage you desire. This shit is so easy a 5 year old could do it.

Same thing I do bro piece of cake