euroroid.is
Subscriber
Yes nylon / PC or on PTFE is very good, but the oil flows very very slowly, CA or PES membranes, the oil flows quickly
Thank you
Thank you
MESO-Rx
Anabolic Steroids
Test prop homebrew recipe
- Thread starter Anabolicbrah
- Start date
I thought its not about the flow but about the resistance to solvents like bb and ba/eo.
Mostly, rate of flow would be my second concern
euroroid.is
Subscriber
all these filter types are resistant to BB / BA and EO, if you need 2-3 hours to filter 200ml then you will need something so the oil flows through faster.
we use the filters that I have already written, it is important that you filter 2x
firstly 0.45 for major pollution, secondly to get a sterile painless solution
Thank you
we use the filters that I have already written, it is important that you filter 2x
firstly 0.45 for major pollution, secondly to get a sterile painless solution
Thank you
My first go at prop was 100mgml plus 10 percent in GSO with 1/10 ba bb. Painless.
euroroid.is
Subscriber
is it stable at 10% BB or has it crashed .. ??
I like to test new recipes in the fridge overnight
Thank you
I like to test new recipes in the fridge overnight
Thank you
I do the same thing. It held. I have some left from almost a year ago. Still good.
Holy fack, only 10bb, amazing
Most of the brews I have made are 15 or less. NPP is right on the edge of 15. Haven’t been able to get tren e to hold at less than 18
Everywhere i read suggestions of at least 18 if not 20% bb for test prop, so thats why im amazed.
You made npp 100 with 14-15 %bb?
Im wondering, prop being short ester, is 10bb enough to keep hormone suspended without crashing in muscle?
Maybe you are just not that sensitive to it, someone get horrid pip from test prop, someon doesnt.
Id love to figure this out.
I guess i have to try myself.
Whats your recipe for 100mg npp? 1/14?
Thanks m8
I’ve heard a lot of conflicting things about prop too. For myself all I know is that the typical 2/18 2/20 on prop leaves me fucking wrecked. Was going to keep pushing through it but then a member on here told me about the prop being brewed at 1/10. I brewed it and have loved it since. You remember the log I made last summer. I was running test p tren a and mast p. All brewed around 10-12 bb. No issues. I ran a blend of all three a few years ago that shit was crippling. As far as NPP goes like I said it’s right on the edge of crashing at 15. You’re on the other side of the pond right. You might not have the weather conditions for 15. You can try 15 and keep it in a warm spot and you might be ok as long as it’s just for you. If you’re brewing for others I wouldn’t go that low.
When we are talking about test prop, masteron and tren ace, you brewed them all around 10-12 bb, in this case does weather-temperature matters to keep it in oil?
You mentioned that NPP at 15 BB is at the edge of crashing.
So during winter I might have a problem with this particular recipe, but previous 3 compounds you mentioned should be ok even during winter?
thank for info
Yeah. No problems with temp on the test tren mast. If you over dose by 10-15 percent at 10bb and it starts to crash where you are you could still add a little more bb and still have around 100mg. Assuming the raws are very pure. If you’re nervous do a small test batch at 10 or just brew at 12 or so bb and you should be fine.
As far as the NPP goes try 15 if it’s for yourself. It did crash on me in the winter but it was cold where I was keeping it and it was very slightly crashed. I would warm the vial and it would go back into solution for a few weeks. Your call. Play with 15 or just go slightly higher and you should be fine.
Awesome, ill give it a go.
Btw. Any chance youve done bloods recently?
Im on just test en blast and on monday ill do bloods but they dont have hormonal panel, so i got to pick up each thing individually for hormones.
Kidney, liver, blood is covered on one package.
Hormone wise i thought to pick up:
Testosterone levels, free test. Levels, estradiol, prolactin, cortisol, shbg.
Anything else im missing,? Do i need both test and free test levels?
Haven’t done bloods in a while. It’s a pain in the ass here. Some states you can order your own. Others have to be done by your doctor. I plan on going this summer to see where I’m at. We have a complete hormone panel so I’m not sure what you’d have to order if it’s by individual hormone. I can tell you that yes def get total and free test levels and make sure the tests aren’t capped. Meaning that if it’s capped it will show test to a certain point. I think like 1500. You could literally be 1501 or 5000 and you wouldn’t know. Def estro and I would think no on the prolactin but if you’re running for example tren or deca definitely get prolactin.
SuperSwede
Member
Why do you use PES or CA?
They are made for waterbased solution not oil
I go with PVDF or Nylon
euroroid.is
Subscriber
all these filter types are resistant to BB / BA and EO, if you need 2-3 hours to filter 200ml then you will need something so the oil flows through faster.
we use the filters that I have already written, it is important that you filter 2x
firstly 0.45 for major pollution, secondly 0,2 to get a sterile painless solution
Thank you
SuperSwede
Member
Ok
I filter 200ml with 10ml syringe and .22 PVDF filter. I have a constant flow and it goes fast.
But whatever. If it works for you then thumbs up.
superbane
Member
Where did you read PES filters being resistant to alcohols?
PES membrane is for sure NOT good resistant to BB,BA,EO . Nylon and PTFE are resistant to all solvents.
Flow depends on
- viscosity of carrier
- temperature of carrier
- vacuum power ( or press )
- type of membrane
ALCOHOLS PES membrane
Benzyl Alcohol, 100% NR - no resist.
Benzyl Alcohol, 3% LR - limited resist.
