Problems making masteron homebrew...

[Musclez]

For some reason i can't get my masteron to hold in solution. I have made many homebrews before, cyp, enanthate, test prop, deca, eq, tren. This masteron is acting odd. I have already added 25% BB and 5% ba and it's not that it's crashing like all my other roids would, it's just looking like undissolved sugar at the bottom that will cloudy the solution when shaken. At this concentration of solvents it should dissolve since im only making it at 100mg/ml. Any suggestions? Another bro on meso only used 20% bb and claims to have made 150mg/ml masteron.
Thanks guys

Musclez

 

[jocko]

sounds weird at the % of bb and ba u are using

 

[chris gordon]

have you heated it back up till the stuff disappears? all the chems in the world wont dissolve until you heat it....put it in apot of 1/2 water on medium heat , heat until there are no crystals left...then heat a few more minutes

 

[conan]

1 ml of BA
9 ml of BB
5 grams of Masteron powder
36 oil

100 mg/50 ml

should work....

 

[muslhead]

I got mine to hold at 100mg/ml with 5%BA and 10%BB
MH

 

[novicebb]

1 ml of BA
9 ml of BB
5 grams of Masteron powder
36 oil

100 mg/50 ml

should work....

36ml of oil seems like a bit. 34 would get you 50ml with the masteron propionate or enanthate displaced

 

[unt0ld]

Homebrew is the shit.

 

[Big_paul]

20% bb that is way more than I have ever heard of any one using as a co solvent. I have never used more than 4-5 percent bb and 1% ba. At those levels I could disolve test prop at 80 -100mg concentrations. I once through some bb in a plastic cup after making some gear and put it up in the cupboard I looked at it 3 weeks later and it ate through the bottom of the cup.That made me think alot about how much bb and ba to use. I can't see how you could even inject it at those levels. Are you sure you have legit goods.

 

[mr.nitro]

id also try heating the gear like other have sugested. I made a small batch of 400mg test and it was a little grainy till I left the vial in a bowl of hot water for a little while. hasn't crashed since.

 

[jboldman]

if needed 20%bb is fine. in fact it is how pfizer makes up human grade Depo Testosterone. Most esters will go at 10%bb.

jb

 

[unt0ld]

We Would All Be Broke Without Homebrew.

Yay For Homebrew!

 

[Aquabol]

For some reason i can't get my masteron to hold in solution. I have made many homebrews before, cyp, enanthate, test prop, deca, eq, tren. This masteron is acting odd. I have already added 25% BB and 5% ba and it's not that it's crashing like all my other roids would, it's just looking like undissolved sugar at the bottom that will cloudy the solution when shaken. At this concentration of solvents it should dissolve since im only making it at 100mg/ml. Any suggestions? Another bro on meso only used 20% bb and claims to have made 150mg/ml masteron.
Thanks guys

Musclez

Hi there, Masteron Prop should be fine with 2% BA you shouldn’t need more than that, the crystals in the bottom are undissolved product what temperature did you reach when heating the product? Did you hold at peak temperature and for how long?

 

[dingg]

Maybe your raw powder is suspect?

 

[klokke23]

Thread has been necroed twice lol

 

[dingg]

My bad, didn't notice date

 

[jJjburton]

This must be an all time record for bumping an old thread..20 years

 

[Denicnut2427]

For some reason i can't get my masteron to hold in solution. I have made many homebrews before, cyp, enanthate, test prop, deca, eq, tren. This masteron is acting odd. I have already added 25% BB and 5% ba and it's not that it's crashing like all my other roids would, it's just looking like undissolved sugar at the bottom that will cloudy the solution when shaken. At this concentration of solvents it should dissolve since im only making it at 100mg/ml. Any suggestions? Another bro on meso only used 20% bb and claims to have made 150mg/ml masteron.
Thanks guys

Musclez

I’ve made mast enth at 250mg in 2%ba 20%bb in mct oil it held just fine and was smooth