MESO-Rx Sponsor AASraw: GMP-Certified Steroid and Peptide API Manufacturer

[amicedrot]

After checking on your raws at the post office in Turkey:


View: https://youtu.be/KyGlCGqAgw0

good news for me is that it is likely the package will show up, it just irritates me for 60$ i cant track it all the way to the end. living on an island and getting a shipment this time of year is always hectic. itll probably turn up in early january. good news is i still have oils to hold me til i need it, i ordered well in advance of need

 

[Bigguy81]

No guiacol, no winstrol injectable as far as I can tell from my experiments. I'll try to revisit it when I have time but last time I pinned 50mg/ml of winstrol done without Guiacol i had PIP for 1 week and a never ending knot in my shoulder plus it crashed 12 hours after I brewed it.

I managed to have it hold at 40mg/ml kinda but still pip city.

I don't know how you got it to hold at 50mg/ml without using G. I'll be honest I'm kind of over making it at this point, but I do have a little left.I can't let it go to waste.lol..

 

[Bigguy81]

20% guaicol 20% bb winstrol vanished at 60 degrees celsius. After one month still didn't crashed

I'm sorry, but I call bullshit. There is no way in hell you're getting it to hold with 20/20 BB/G.

 

[Bigguy81]

20% guaicol 20% bb winstrol vanished at 60 degrees celsius. After one month still didn't crashed

This is the only way you're getting it to hold with 20%BB, and 20%G, did you leave out that you used EO as the carrier

Winstrol Oil based @50mg
1% BA
20% BB
20%G
Carrier=EO

 

[Bigguy81]

Which brings me to the point I was making, that while not needed… Would it not make sense to just bring it to the melting point regardless of solvents? Because better safe than sorry. I don’t see any damage being done by bringing it to melting point.

Personally, I don't think it hurts the compound to bring it to the melting point for a short period of time. However, I also don't feel as though it's necessary when using the correct amount of solvents though..

 

[Stauros3315]

I'm sorry, but I call bullshit. There is no way in hell you're getting it to hold with 20/20 BB/G.

I can show you photos if you like. And Yes the carrier is EO

 

[Bigguy81]

I can show you photos if you like. And Yes the carrier is EO

No, you don't have to do that. I can believe you now that you say the carrier was 100%EO. I've been able to get it to hold with that recipe, but i feel like you have to use a lot of heat or at least I had to. and make smaller amounts. Less than, say 400ml at time. Also, it always seems to hold in the media bottle, but weeks after being in a 10ml vial a few might crash. Does anybody else notice the same thing? Also, If you don't mind me asking, what temperature are you bringing it to, and for how long?

Thank you for being able to have a conversation, and not an argument.

 

[Stauros3315]

No, you don't have to do that. I can believe you now that you say the carrier was 100%EO. I've been able to get it to hold with that recipe, but i feel like you have to use a lot of heat or at least I had to. and make smaller amounts. Less than, say 400ml at time. Also, it always seems to hold in the media bottle, but weeks after being in a 10ml vial a few might crash. Does anybody else notice the same thing? Also, If you don't mind me asking, what temperature are you bringing it to, and for how long?

Thank you for being able to have a conversation, and not an argument.

The process i Made is add 5g winstrol 20% guiacol 20%bb only heated to 60 degrees celsius for 5-10 minutes at stable temperature until all powder is melted then added the EO and the whole process took about 20 minutes

 

[watchtymeflyyy]

Personally, I don't think it hurts the compound to bring it to the melting point for a short period of time. However, I also don't feel as though it's necessary when using the correct amount of solvents though..

What is the “correct amount of solvents?” I feel like that is highly subjective while the melting point is an absolute.