MESO-Rx Sponsor AASraw: GMP-Certified Steroid and Peptide API Manufacturer

[dinfar1337]

Personally i just dump all liquids in first then raws last
Overtime you'll have your own preference on how to do things

205c needed for benzyl alcohol to evaporate at a significant speed

as long as you're not brewing the same ba for 20 days over or using 500c for your brew its better to add ba in start for sterility

 

[Neegan02]

Brewed a trial vial of TNE 50 with MCT last night. Wasn’t able to dissolve raws at all when I put it in liquids which did not surprise me.

It did dissolve after I melted the raw first for 2 mins with the warmed liquids after. It is starting to recrystallize this morning as expected… was hoping to avoid EO, but what advice would y'all have for keeping TNE dissolved in solution?

 

[Photon]

Brewed a trial vial of TNE 50 with MCT last night. Wasn’t able to dissolve raws at all when I put it in liquids which did not surprise me.

It did dissolve after I melted the raw first for 2 mins with the warmed liquids after. It is starting to recrystallize this morning as expected… was hoping to avoid EO, but what advice would y'all have for keeping TNE dissolved in solution?

2/40

 

[amicedrot]

Put the measured bb in your beaker then your raws in the same beaker as your bb . Slowly heat and stir .

While it’s melting you want your measured amount of oil heating also in a separate beaker .

Once the raws are fully dissolved. Then slowly add your oil and stir till you see no more swirls . It’s actually pretty important that there are close to the same temperature when mixing them.

Then remove beaker from any heat source.

Then add in your measured ba . Then stir till there are no more swirls .

Do it this way and your ba will not evaporate or get damaged from heat. You need it to keep no bacteria growth so you don’t get abscesses .

Now to help with filtering , if you have the time to filter it right away while the oil is still warm, it helps speed up the process.

i bought the exact hot plate with mag stirrer from the recommended homebrew shopping list, so i have the ability to control temp accurately damn thing was almost 200$ it better be accurate. also invested in a nice vacuum pump and lab stand setup for filtering into pre-sterile vials. since its only for personal use it doesnt matter to me if i flip the tops off already, i already know what ima put inside hehe. id be willing to learn the temps and all that, but since im a few weeks out i dont mind waiting and then revisiting in the homebrew section. that said i do appreciate the advice.

 

[The-Squat]

205c needed for benzyl alcohol to evaporate at a significant speed

as long as you're not brewing the same ba for 20 days over or using 500c for your brew its better to add ba in start for sterility

Only time I don't add BA 1st and do it last is withTren A, otherwise dump the raws in a beaker add BA add BB and then turn on the spinner and heat. Add warm oil to dissolved raws and spin more.

I leave it on 120F to 130F to stay warm during the filtration process on large batches which is all the time for me.

All this rocket science is pretty funny don't you think? LOL.

 

[The-Squat]

There is more than 1 way to skin a cat, if it works for you it works but I'd never heat the raws 1st alone without BA and BB especially Tren A, but my batches are larger than most.

 

[Fizzik]

i bought the exact hot plate with mag stirrer from the recommended homebrew shopping list, so i have the ability to control temp accurately damn thing was almost 200$ it better be accurate. also invested in a nice vacuum pump and lab stand setup for filtering into pre-sterile vials. since its only for personal use it doesnt matter to me if i flip the tops off already, i already know what ima put inside hehe. id be willing to learn the temps and all that, but since im a few weeks out i dont mind waiting and then revisiting in the homebrew section. that said i do appreciate the advice.

What’s a lab stand setup consist of? Interested for exact same scenario for self brewing.

 

[Photon]

What’s a lab stand setup consist of? Interested for exact same scenario for self brewing.

Its to hold beakers etc
I use one to hold my caulk gun