MESO-Rx
Anabolic Steroids
accidently put too much ba in brew
- Thread starter hampros2
- Start date
It's still good... Typically would cause some PIP but if it doesn't hurt, should be good to go.
Clamslaps
Member
I've put like 5% ba in something when I couldn't get my hands on sterile water living out of the country for a minute, it will sting like a bitch until you're used to it but otherwise not going to hurt you.
Ridethelightningbarefoot
Member
Ba and/or bb tears me up! I made t cyp and bold cyp both at 2% ba and 18%bb and I was crippled because I draw them up at the same time. I have draw up sterile oil with it so I can function normally. I usually don't get pip until like 12hrs after but 48 hrs I'm dying haha
Meterman05
Member
I don't think it was the BB or BA that is causing the PIP bud. Bold cyp is a compound known to give PIP. Same as the compound DHB is known to give some PIP regardless of how it's made. Try injecting just the test cyp and bold cyp separately and see if it's both. My bet is the bold cyp is what's doing it to you.
Ridethelightningbarefoot
Member
I have done this in the past and there is no difference.
This was the first time I brewed test c. And I was afraid of it crashing so I used a higher amount than usual. My last brew was barrable because I used lower ba and bb. I am thinking about trying some concentration at what some old threads recomend. And a article bill Jones wrote on here. In the thread they talk about brewing test c at 4% bb with no issues. And bill Jones talks about using .08% ba or no ba with no issues. Also I love bold c I may just suffer to keep running it. I had my buddy try it and he didn't have any problems at all! I am a pip unicorn!
Last edited:
Test cyp will not hold at 4%bb. The recipe I use is 1-2%ba and 18%bb and it only crashes in 30 degree weather. Also there is no pip with it. Im going to side with @Meterman05 here and say that it’s the bold cyp that is making you hurt. I see you said this was your first time with test Cyp. Try it alone and see. If you were using test e prior to this, it has been known to have a decent amount of pip at times. That’s why I only brew test cyp.
Ridethelightningbarefoot
Member
I have pinned test e and test cyp separately from the bold and the bold hurts only a little worse. I will prob just go back to my most painless brew which was 15bb(maybe less)and 1ba.
Meterman05
Member
@Ryan owen what carrier oil are you injecting? Have you tried different ones? I believe that you get the PIP you are saying it's just weird that cyp with 15% BB gives it to you. I have brewed cyp with 25% BB and didn't get any PIP. I have found for me PIP is related to certain compounds. For example I can't inject enanthate without PIP(reason I went to cyp). I get some from prop. No matter what site I injected those two always gave me PIP.
My opinion on PIP is that it's mainly related to compound and the strength (there is only so much room in a mL of carrier oil to fit hormone in it) . I feel that lower BB is actually worse than higher as I would rather the compound be completely suspended. My feeling are that the only solvents that increase PIP are BA and guaiacol. I have never tried EO so I can't say if it does. Even now I use mig840 I never make anything with less than 20%BB. I brew for myself about 6 other guys. None have any PIP.
My opinion on PIP is that it's mainly related to compound and the strength (there is only so much room in a mL of carrier oil to fit hormone in it) . I feel that lower BB is actually worse than higher as I would rather the compound be completely suspended. My feeling are that the only solvents that increase PIP are BA and guaiacol. I have never tried EO so I can't say if it does. Even now I use mig840 I never make anything with less than 20%BB. I brew for myself about 6 other guys. None have any PIP.
Ridethelightningbarefoot
Member
I started with mct and it was unbearable. Switched to gso and that was better. Concentration is def a huge factor. I tried brewing bold c at 200mg and it is terrible so I went down to 150 and it's better. My friend tried it recently with no issues. I am currently having to draw up oil to dilute. I have a couple months at least in the batch so I will have to wait it out. 15bb and 1ba was manageable I didn't get much pip
Similar threads
