Arail Pharmaceuticals - US Domestic

[Vikingo]

Thanks guys.

@Vikingo the intermittent nature of the PiP makes me think crystals and less so MiG issue. If it were the MiG it’d happen every time no?

Yes I agree Rocky it has to be crystals even though I heat the fuck out of mine every time. When I go back on blast I’m going to leave it on my warmer for a longer period of time and see if that does the trick. A little PIP never discouraged me it builds character.

 

[Alvinq]

I have had the same experience with the TNE. I use the same protocol heating etc. sometimes PIP sometimes none.

Same here. It seems to be completely random.

 

[RockyP]

Same here. It seems to be completely random.

For the TNE are we talking just pip or also redness / swelling? That’s what I’m still getting inconsistently from the anadrol which is making me think it’s a MiG issue, though if it were from the MiG I don’t think it would be so inconsistent.

 

[Vikingo]

For the TNE are we talking just pip or also redness / swelling? That’s what I’m still getting inconsistently from the anadrol which is making me think it’s a MiG issue, though if it were from the MiG I don’t think it would be so inconsistent.

On the occasions there’s been PIP there’s been no redness or swelling except for one delt injection where I had some redness but no swelling. All my injections have been a full ml with the TNE heated to 150 degrees +. I was running a full ml in each delt or quad and sometimes only one would get PIP, completely random.

 

[RockyP]

On the occasions there’s been PIP there’s been no redness or swelling except for one delt injection where I had some redness but no swelling. All my injections have been a full ml with the TNE heated to 150 degrees +. I was running a full ml in each delt or quad and sometimes only one would get PIP, completely random.

Thanks brother. I’ve got no redness swelling or pip from my last Anadrol shot. Only difference was heating it higher for longer. Than may be the ticket for me.

 

[Alvinq]

For the TNE are we talking just pip or also redness / swelling? That’s what I’m still getting inconsistently from the anadrol which is making me think it’s a MiG issue, though if it were from the MiG I don’t think it would be so inconsistent.

It's typically just pip/discomfort but in a kind of sharper way if that makes sense. The shot to my delt yesterday left a small temporary lump though.
I always throw the vial on the warmer for 15-30 mins before and sometimes cut it with Mast P.
This is all with the TNE only and it's not enough of a problem to deter me from using my last 2 vials.
My thinking is if it was a reaction to the Mig I'd have it on every shot. Maybe? Does that make sense?

 

[Photon]

Thanks brother. I’ve got no redness swelling or pip from my last Anadrol shot. Only difference was heating it higher for longer. Than may be the ticket for me.

It's typically just pip/discomfort but in a kind of sharper way if that makes sense. The shot to my delt yesterday left a small temporary lump though.
I always throw the vial on the warmer for 15-30 mins before and sometimes cut it with Mast P.
This is all with the TNE only and it's not enough of a problem to deter me from using my last 2 vials.
My thinking is if it was a reaction to the Mig I'd have it on every shot. Maybe? Does that make sense?

Before pinning i heat it on the highest setting and then shake it.
It's too hot to pin or draw, wait for it to cool down a little, draw then pin.

Highest setting on mine is 176f.

Go slow when you pin. Yes its smooth, but don't inject it like injecting hgh lol.
Go slow nice and easy.

 

[Vikingo]

Before pinning i heat it on the highest setting and then shake it.
It's too hot to pin or draw, wait for it to cool down a little, draw then pin.

Highest setting on mine is 176f.

Go slow when you pin. Yes its smooth, but don't inject it like injecting hgh lol.
Go slow nice and easy.

Good to know! I thought I was heating mine up at enough at 150 F., sounds like I need to crank up the heat some more!

 

[RockyP]

Before pinning i heat it on the highest setting and then shake it.
It's too hot to pin or draw, wait for it to cool down a little, draw then pin.

Highest setting on mine is 176f.

Go slow when you pin. Yes its smooth, but don't inject it like injecting hgh lol.
Go slow nice and easy.

Thank you for this pro tip sir!

 

[dcfreak]

I haven't seen / heard / read about any issues with injectable SD crashing. Has anyone had this experience? I ask because I'm still fighting with my injectable anadrol and trying to figure out if it's the MiG or the crashed crystals I can't see. I had 4 shots in a row without pip / redness / swelling but then it happened again. Same heating protocol. Higher (145F) seems to be better. So, I wanted to try something else in MiG to see if I get the same reaction. I'm guessing SD would be the one to try, even at a miniscule dosage, rather than TNE due to the propensity for TNE to also crash, yes?

Never had injectable SD crash

 

[dcfreak]

My anadrol and TNE from Arail have not crashed at all at room temp- haven't needed to heat either or keep them in the warmer.

Now- homebrew Anadrol from my homeboy absolutely needs a hotplate once a week and to be stored in the warmer.

 

[RockyP]

My anadrol and TNE from Arail have not crashed at all at room temp- haven't needed to heat either or keep them in the warmer.

Now- homebrew Anadrol from my homeboy absolutely needs a hotplate once a week and to be stored in the warmer.

Just wondering how long have you had the anadrol for? Mine lasted at room temp for about a week then I woke up morning and it was totally crashed.

 

[dcfreak]

Just wondering how long have you had the anadrol for? Mine lasted at room temp for about a week then I woke up morning and it was totally crashed.

Order was placed Dec 20.

Just went and looked at all the vials from Arail from that order- anadrol, superdrol, TNE, etc.

Nothing is crashed at all.

Like I mentioned, though- all the homebrew is crashed and needs heat beyond just the warmer to get back in solution.