Castor oil experiments

Never got around to brew Test P.

DHB is 1.5/30. No crashing no pip
I have yet to homebrew with a melting point so close to the carriers smoke point,

Do you take the solution all the way up to 190°C or do you hover around a lower temp just getting near it?

It seems wise to make smaller batches, I'd wonder the longevity of the carrier being brought so close to degradation
 
I have yet to homebrew with a melting point so close to the carriers smoke point,

Do you take the solution all the way up to 190°C or do you hover around a lower temp just getting near it?

It seems wise to make smaller batches, I'd wonder the longevity of the carrier being brought so close to degradation
Both BA and BB lowers the mp so I go up to 90-95 WITHOUT the solvents and then dump them after I lower the heat down to 60
 
Maybe could be interesting.
In an acceptable embodiment, the viscosity of the mixture of castor oil and cosolvent taken in a volume ratio of 1: 0.02 is reduced by about 10% with respect to the viscosity of castor oil. In other embodiments, when the volume ratio of oil to cosolvent is 1: 0.04, the viscosity decreases by 20% with respect to the viscosity of castor oil, when the volume ratio is 1: 0.08, the viscosity decreases by 25% when the volume ratio is 1: 0.1, the viscosity decreases by 40% when the volume ratio is 1: 0.2, the viscosity decreases by 50% when the volume ratio is 1: 0.35, the viscosity decreases by 75% when the volume ratio is 1 : 0.5, viscosity decreases by 80% when the volume ratio is the solution is 1: 1, the viscosity is reduced by 90%, or when the volume ratio is 1: 1.6, the viscosity is reduced by 95%.
 
Interesting would you tell more about temps in how you don't sir
Just see below. :) About Testosterone Undecanoate
(C)”Then the final solution can be filtered through a filter with a hole size of 0.2 μm, it is not necessary to add, for example, into yellow glass bubbles, and then finally sterilize at 180 ° C for 3 hours.”
 
Just see below. :) About Testosterone Undecanoate
(C)”Then the final solution can be filtered through a filter with a hole size of 0.2 μm, it is not necessary to add, for example, into yellow glass bubbles, and then finally sterilize at 180 ° C for 3 hours.”
Say what the melting point is what I was asking him about bro
 
New year, new experiments

Test D 500mg/ml 40%BB Castor
Test Iso 400mg/ml 40%BB MCT
TPP/NPP Blend 150mg/150mg 40%BB Castor

Holding so far, will recheck in a couple of days

View attachment 310080
Is 40% bb for test iso necessary for maintaining decent viscosity or for not crashing at low temp?
Haven't found any recipes for test iso and planning to brew some but got no clue what ratios
 
Is 40% bb for test iso necessary for maintaining decent viscosity or for not crashing at low temp?
Haven't found any recipes for test iso and planning to brew some but got no clue what ratios
Crashing. It's the initial experiment, I will prob go down next time. I am ok with high BB so not concerned
Why 40bb for MCT oil narta?
See above. Initial experiment.

When Ethyl Lactate comes I will first use it for Test base and maybe incorporate it to all the others as a "super solvent" and reduce BB to half or less.
 
Crashing. It's the initial experiment, I will prob go down next time. I am ok with high BB so not concerned

See above. Initial experiment.

When Ethyl Lactate comes I will first use it for Test base and maybe incorporate it to all the others as a "super solvent" and reduce BB to half or less.
Wow what's ethyl lactate? Something like EO but not toxic?did you try to pin the npp/tpp to see if it's PIPless?
 
Last edited:
Less oil volume to inject it's just better overall. More rotation available and less scar tissue too

Even if you don't do big blast it's still better and it's PIPless with these compounds

Thanks. I reading the thread and saw these comments...
I can lower injection volume significantly

2.5ml in the shoulder no pain,

You guys aren't messing around, lol.

I've been injecting for 7 years with most of that time 27 or 29 g. No hint of any scar tissue.

Cool thread. Narta does his HW.

Appreciate all the effort and sharing the info/results.
 
Thanks. I reading the thread and saw these comments...




You guys aren't messing around, lol.

I've been injecting for 7 years with most of that time 27 or 29 g. No hint of any scar tissue.

Cool thread. Narta does his HW.

Appreciate all the effort and sharing the info/results.
I have injected most of my years with 23G lol

Just started in the last few years to appreciate 27g and 25g.

With high concentration oils I can PIN the same muscle once every few weeks, if I'm not blasting much volume, let's say I do a 1g Test and 1G EQ cycle

That's 2ml of test D 500 and 2 ml of EQ 500

I can pin that anywhere from shoulder to VG to glutes to quads.

So I can do glute 1 - glute 2 - shoulder 1 - shoulder 2 - VG 1 - VG 2 - quad 1 - quad 2 and after 8 weeks I'll pin again the glute. Not bad isn't it?

Let's say I wanna go higher on the volume I can easily do 2ml glute + 1ml smaller muscle 2x a week and do 1G test 1G EQ and 800mg Masteron for example or 800mg Deca

Many possible combination with very low volume :) plus lower volume of oil, faster absorption, you can pin again the same muscle quicker
 
Back
Top