Cloudy Bold Cyp after heating.

[ebkallday]

I already posted this thread in the regular steroid forum but probably should have posted here to begin with. I have yet to get an experienced answer, though got some good responses. Some of the guys guessed it was air, or maybe moisture.

I dont brew but thought someone who does may have some insight.

I have Bold Cyp from a ugl. All my vials crashed and the rubber stoppers started to fall apart. So I heated all the vials in a pan of hot water for 15 minutes and shook them periodically till the crystals dissolved back into liquid form. I filterd them all through a couple whatman filters and got clean looking oil. I got to the last vial and noticed it was cloudly and not clear like the rest of the vials. I figured maybe I didn't heat it long enough to fully dissolve and heated it again. The oil stayed cloudy and even after cooling.

My question is, what the shit happend? And would I be safe to just filter and use? The shit was $50 a vial and I rather not just throw it out if I don't have to.

 

[psilikon]

That is terrible. Fuck. Can you contact the UGL and send them some pics and try to get a portion of your proceeds back? What is the concentration? The rubber stoppers are actually falling apart? Wtf. The last vial is probably contaminated with water. You could try to 'cook' out the water. I'd go with contacting the UGL.

 

[johnnyBALLZ]

Ebk, brotha man, you need to contact Astro and have him make this right.. I wouldn't let a few hundred bucks slide like that..

Just sayin'..

 

[ebkallday]

E="johnnyBALLZ, post: 1038983, member: 60898"]Ebk, brotha man, you need to contact Astro and have him make this right.. I wouldn't let a few hundred bucks slide like that..

Just sayin'..[/QUOTE]
Yeah, I pmed Astro and he was very reluctant to offer a %50 percent refund with pics. He said I was lucky he was willing to do that for me after its been 8 months from the time I received the Bold and no other UGL would be that generous. It offended me a little, since I was running his shit back when P22 and Myth were doing logs for him. I threw down good reviews and recommended several members to him. This is the thanks he gives me? It wouldn't effect his sales one bit if he would have just told me to shuv them up my ass. Fuck him. Boys to big for his own britches.I'll just trash the cloudy vial, run the filtered stuff and toss in mast p to cover the lost 10mls

 

[johnnyBALLZ]

E="johnnyBALLZ, post: 1038983, member: 60898"]Ebk, brotha man, you need to contact Astro and have him make this right.. I wouldn't let a few hundred bucks slide like that..

Just sayin'..

Yeah, I pmed Astro and he was very reluctant to offer a %50 percent refund with pics. He said I was lucky he was willing to do that for me after its been 8 months from the time I received the Bold and no other UGL would be that generous. It offended me a little, since I was running his shit back when P22 and Myth were doing logs for him. I threw down good reviews and recommended several members to him. This is the thanks he gives me? It wouldn't effect his sales one bit if he would have just told me to shuv them up my ass. Fuck him. Boys to big for his own britches.I'll just trash the cloudy vial, run the filtered stuff and toss in mast p to cover the lost 10mls[/QUOTE]


Oh really?? Hold on...

 

[calfcramp]

My experience w/ cloudy gear. F!!!!!!ck!. I found that a higher concentration of EO breaks down filters made w/ plastics. Polypropylene and nylon are typical in filters we use. EO will melt/ dilute these polymers. I've had the filter peal away from the BT during filtration and begin to particulate. I stopped using EO and have not had the problem again. My experience and it's all I can offer. Weather it's the case or not I'd run it by Mr. Astro.

 

[calfcramp]

http://www.interplexindia.com/aca.htm