Drawing from ampules - having problems

[mr_meanor]

I have been using iranian test E and some of satches primos and i am having a hard time getting all the juice out of the amp. I only usually get about 3/4 of a ml cause I can't suck the last little bit of it up and some you lose when you are getting rid of the air bubbles. anybody got any tips on how I can draw all the gear from the amp or is there some technique to it I am unaware of?

any input is appreciated

 

[pumppumppuk]

are you drawing with an 18?


PPP

 

[mr_meanor]

are you drawing with an 18?


PPP

no a 21 and shooting with a 23

 

[patsfan]

no a 21 and shooting with a 23

You need to use an 1 1/2 inch to get it out then switch back to your 1. I get every last molocule with the 1.5

Or tip it so the juice comes to the top of the ledge and draw like I have to do with the pregnyl (long ass vial)

Pats

 

[Southernjuice]

To draw from an amp you break the top off and turn it upside down, yes you heard right, upside down and draw it out. You will leave nothing this way and amps are made to be used this way....the liquid will not spill bro.

 

[patsfan]

To draw from an amp you break the top off and turn it upside down, yes you heard right, upside down and draw it out. You will leave nothing this way and amps are made to be used this way....the liquid will not spill bro.

Damm you learn something new every day.

 

[pumppumppuk]

i can never get amps to open right, so i get a triangle file and score it. use a pen top to pop it open. use an 18 to draw as much as i can, and tilt it forward so that the remaining oil rest on the curved top edge and draw it up. i usually get damn near the whole ml out. then i let it stand up on the plunger while i prep my skin, so that the air bubbles float to the top. you can gently thump it to get the air bubbles that are stuck to the side to rise up.


hope this helps



PPP

 

[pumppumppuk]

To draw from an amp you break the top off and turn it upside down, yes you heard right, upside down and draw it out. You will leave nothing this way and amps are made to be used this way....the liquid will not spill bro.

damn...... im going to try this in the morning. sounds better than my way.




PPP

 

[mr_meanor]

To draw from an amp you break the top off and turn it upside down, yes you heard right, upside down and draw it out. You will leave nothing this way and amps are made to be used this way....the liquid will not spill bro.

interesting I will try this tomorrow as well, thanks bro

 

[Southernjuice]

No prob....have used thousands of amps and always have done this. Keeps ya from dulling your needle as well.

 

[pumppumppuk]

To draw from an amp you break the top off and turn it upside down, yes you heard right, upside down and draw it out. You will leave nothing this way and amps are made to be used this way....the liquid will not spill bro.

im calling bs.....i tried this morning with sust, and poured out like a faucet. i made sure i had a clean break...turned it upside down.....and started cursing.




PPP

 

[MANWHORE]

im calling bs.....i tried this morning with sust, and poured out like a faucet. i made sure i had a clean break...turned it upside down.....and started cursing.




PPP

Yeah,i get that same problem when i turn my glass of orange juice upside down
Damn gravity

 

[MANWHORE]

I have been using iranian test E and some of satches primos and i am having a hard time getting all the juice out of the amp. I only usually get about 3/4 of a ml cause I can't suck the last little bit of it up and some you lose when you are getting rid of the air bubbles. anybody got any tips on how I can draw all the gear from the amp or is there some technique to it I am unaware of?

any input is appreciated

I always use an 21g 1 1/2in pin to draw up aas whether it's from and amp or a vial. If i do site injects,i will switch to a 28 or 25g but when i go in glute,i stay with the 21 or maybe it's 22g 1 1/2. Something like that but i never had a problem getting all liquid from amps. The suction from the pin always got most of it. Of course there's always going to be a drop.

 

[mr_meanor]

im calling bs.....i tried this morning with sust, and poured out like a faucet. i made sure i had a clean break...turned it upside down.....and started cursing.




PPP

atleast I wasnt the only one gullible enough to try this, figured shit maybe it works and gave it a shot, hell no a wasted amp of iranian test enethate was I got out of it

 

[MANWHORE]

atleast I wasnt the only one gullible enough to try this, figured shit maybe it works and gave it a shot, hell no a wasted amp of iranian test enethate was I got out of it

LMAO
I'm trying to picture how it looked when you turned it upside down. Better yet,how you looked

 

[Southernjuice]

atleast I wasnt the only one gullible enough to try this, figured shit maybe it works and gave it a shot, hell no a wasted amp of iranian test enethate was I got out of it

Well not doubting it happened but i've done literally thousands of amps this way and...just did it that way again, worked fine. Don't hold it at an angle ,it must be completly inverted, however, don't think you'll give it another try though. Sorry...I even do water based ampules this way and never have they just spilled out.

 

[Southernjuice]

im calling bs.....i tried this morning with sust, and poured out like a faucet. i made sure i had a clean break...turned it upside down.....and started cursing.




PPP

This was'nt meant as a joke either by the way....maybe it is the technique I use(??) cause i'm in the med. field and do this everyday.....sorry again....pouring the shit in the floor is steroid abuse of the worst kind bro.

 

[Southernjuice]

Hell I might call BS Just done it again with no probs and just for the hell of it when I finished I filled the amp with a ml of water and turned it upside down and drew that without a problem also.....actually guys that is the way amps are supposed to used ,don't know what you done wrong...maybe you turned it over to slow.

 

[madman]

I break the amp with a amp opener after flipping the top to get the little bit of juice that is cought up to drop down. I then take a 18ga. 1.5" pin and suck everything out of the amp holding it at a 45 degree angle with the pin opening facing against the glass. While warming up the steroid in the dart under warm water I flip the barrel to get all of the bubbles to go up. I switch over to my new sharp 25ga and bam I'm juiced.

 

[pumppumppuk]

well i feel better now that you said it was not a joke, but i wont be trying that again any time soon....lol


manwhore,

yea, i would have liked to have seen my face when that shit hit the counter too. im glad i dont have any kids because my language this morning was awful.



PPP