First home brew

[incrediblebulk]

I brewed test e @ 250mg/ml with 2 ba 18bb ten vials everything went according to plan. I notice two days later one of the ten vials had crashed on me.

Any thoughts on why this would occur? Did it cool too fast before filtering?

Thanks

 

[incrediblebulk]

After searching it may have been condensation

 

[alphastrength50]

how hot was the oil when you filtered it?

 

[incrediblebulk]

I don't know the exact temp or if it was one of the last vials filtered. I will have to check on my next round.

 

[incrediblebulk]

The gear is cloudy not crashed. I used three whatman filters per the ten vials also. So I don't think I blew out my filter

 

[Xodusforever]

Boil a small amount of water. Small is relative, so depending on the pot, just fill it with enough to come up halfway on your vials. Remove the pot from heat, and either hold your vial in half way or stand it there if it's stable.

Your cloudiness will disappear after a few minutes. What comes out after that will be whole crystals. Adjust with more solvent next time if more than a salt grain or two.

 

[Mus4]

Steps (from anabolic underground book) - pharma manufacturing steps simplified -

1. put oil & Benzyl Benzoate in tank >heat to 150 C, heat further 30minutes.

2. Turn off the heat, cool it to 80 C

3. Add powder & Benzyl Alcohol

4. cool it to 25 C

5. Filter

_____________
I don't know why pharma heats them at 150C for 30min...Guessing maybe for sterilization? (Does anyone know why??) However, if pharma is doing this way I will just follow them, and it works great for me.

 

[rutman]

Steps (from anabolic underground book) - pharma manufacturing steps simplified -

1. put oil & Benzyl Benzoate in tank >heat to 150 C, heat further 30minutes.

2. Turn off the heat, cool it to 80 C

3. Add powder & Benzyl Alcohol

4. cool it to 25 C

5. Filter

_____________
I don't know why pharma heats them at 150C for 30min...Guessing maybe for sterilization? (Does anyone know why??) However, if pharma is doing this way I will just follow them, and it works great for me.

Never seen this method before... I'll have to try it next time


Sent from my iPhone using Tapatalk

 

[calfcramp]

Use 20% BB

 

[incrediblebulk]

Use 20% BB

You are more experienced than I am but some recipes don't call for bb at all. Will this remedy the problem? I will gladly at the extra 2 percent. Thanks

 

[calfcramp]

Test e shouldn't be giving you a problem... but it is. Go with 20%

 

[calfcramp]

You are more experienced than I am but some recipes don't call for bb at all. Will this remedy the problem? I will gladly at the extra 2 percent. Thanks

It's giving you a problem. Use 20%

 

[incrediblebulk]

Thanks man

 

[iintensity]

It's most likely do to some impurity. Don't list to the fuckers saying add more solevents, test e is soluble in oil.

 

[calfcramp]

It's most likely do to some impurity. Don't list to the fuckers saying add more solevents, test e is soluble in oil.

I'm a fucker?

 

[03xx52]

It's most likely do to some impurity. Don't list to the fuckers saying add more solevents, test e is soluble in oil.

"Do" to your piss poor command of the English language, I am inclined to believe that you do not know shit...What impurities would present it self like this?

 

[Ricardo]

It's most likely do to some impurity. Don't list to the fuckers saying add more solevents, test e is soluble in oil.

BRAVO! You're being a grade A dick! Not going to end well for you!

 

[calfcramp]

The gear is cloudy not crashed. I used three whatman filters per the ten vials also. So I don't think I blew out my filter

No EO?

 

[incrediblebulk]

Nope

 

[calfcramp]

Nope

Not sure why that happens. I cut back on eo and it helped. It always seems to happen toward the end of filtration. I was thinking it's because the solvents break down the filters. The gear goes through clear on the source end then is cloudy on the supply side. Still a mystery.