Guaiacol Free Injectable anadrol/superdol

Look into ethyl lactate to replace guaiacol. Never tried myself as I don't take injectable orals steroids but I read on meso france that it might work.
 
BA/BB is enough, no need to add anything else..
Even for anadrol ? I’ve heard sdrol is pretty manageable but most of the injectable adrol I’ve seen contains guac or EO so I’ve always assumed that anadrol is harder to brew without super solvents
 
BA/BB is enough, no need to add anything else..
I made 50mg/ml anadrol with BA/BB and guaiacol and it would still crash. I diluted it down less than 40mg with more guaiacol and it would still only hold for a few days before needing to be heated again.
 
You only have 2 options if the 2/18 & MCT oil does not hold; 1) Ethyl Lactate instead of the Guiacol, & 2) Use some volume of Ethyl Oleate. Pure EO will after maybe 6 months start dissolving the stopper.
I wish I could tolerate the EO. But thanks for the info. I think I might try the Ethyl Lactate route once I grab some raws and report back !

Per the supergrok

Bottom Line for Your Use Case
At the 10–25% concentrations you would use for injectable Anadrol or Superdrol, ethyl lactate is considerably safer for humans than guaiacol and has a better safety margin than high percentages of benzyl benzoate or ethyl oleate.
No evidence exists that it raises CRP or causes inflammation beyond the steroid itself.
If you keep total injection volume reasonable (≤2 mL per site) and brew sterile, ethyl lactate is currently the least problematic high-power solvent available to the homebrew community.
 
I wish I could tolerate the EO. But thanks for the info. I think I might try the Ethyl Lactate route once I grab some raws and report back !

Per the supergrok

Bottom Line for Your Use Case
At the 10–25% concentrations you would use for injectable Anadrol or Superdrol, ethyl lactate is considerably safer for humans than guaiacol and has a better safety margin than high percentages of benzyl benzoate or ethyl oleate.
No evidence exists that it raises CRP or causes inflammation beyond the steroid itself.
If you keep total injection volume reasonable (≤2 mL per site) and brew sterile, ethyl lactate is currently the least problematic high-power solvent available to the homebrew community.
Have any luck finding a decent recipe or do you think you’re gonna go the ethyl lactate route ? I think I’m just gonna try and get it to hold at 30mg/ml and just use mig840 , ba, and bb. I’ll report back in a couple weeks !
 
Have any luck finding a decent recipe or do you think you’re gonna go the ethyl lactate route ? I think I’m just gonna try and get it to hold at 30mg/ml and just use mig840 , ba, and bb. I’ll report back in a couple weeks !

Try 2/35
Adrol right?
 
Have any luck finding a decent recipe or do you think you’re gonna go the ethyl lactate route ? I think I’m just gonna try and get it to hold at 30mg/ml and just use mig840 , ba, and bb. I’ll report back in a couple weeks !
Ethyl Lactate should eliminate the need for BB. 1ml per gram should dissolve any esterless hormone. I would advise against Mig - unless someone knows how to use it with mct oil in some sort of mix.
 
Why don’t you like MiG on its own ?

Ive been having great success with 840, however it does seem like a number of people develop an adverse reaction to it over time, as reported on this forum.

These are the oil breakdowns components
MIG812 -> Glycerol and FFA
MIG840 -> PG + FFA
EO -> Ethanol + FFA

840 breaks down to PG, which seems like a pretty common allergen.
Either way, MCT (Mig812) will work.

 
Back
Top