which vendors
MESO-Rx
Anabolic Steroids
Guaiacol Free Injectable anadrol/superdol
- Thread starter mongo5165
- Start date
Photon
Member
Arial and OEP has it.
I started brewing mine recently too.
They use different oil so you have a choice.
what for europe mate
Photon
Member
RockyP
Member
Just throwing in experience of end user with Anadrol 50 in Mig840. First few pins were smooth with no issues. Now seem to be getting some PIP, manageable but noticeable. No redness or anything but def some inflammation. Unclear if it’s the mig840, the extra solvent, or the API. Had similar issues with primo 200 in MCT which leads me to think it might not be the mig840.
@Photon when you referred to PG as allergen did you mean that it causes actual allergic reaction like itching / redness or more just irritant causing lumps / pip etc
@Photon when you referred to PG as allergen did you mean that it causes actual allergic reaction like itching / redness or more just irritant causing lumps / pip etc
Photon
Member
You'll know if there's a allergy reaction..
Localized rash, itchyness, red bumps.
Adrol isn't as easy to hold it seems, it does form crystals if you leave it alone for a week. I'd treat each pin as if it were a crashed vial which requires uncrashing and then revaluate.
RockyP
Member
Ok. Thats what I’ve been doing since the PIP crept up. Warming before pinning. It’s getting better. No itch / rash / bumps. Thanks brother.
bobmyer12541
New Member
so after reading all this a few times, the consensus is that anadrol will gold with 2% BA / 35-40% BB Mig840 at 50mg/ml? about to give it a shot. maybe it crashes after a week but thats nothing. will warm before i inject.
Photon
Member
2/50 holds for a week before crashing.
If you're heating it up it doesn't matter tho.
Anything that doesn't crash in a few days is usually gtg.
bobmyer12541
New Member
okay awesome thank you for the response. is 2% BA needed as well? i usually do 1% in my brews and never have issues. to my knowledge the extra 1% BA is just for a safety threshold? ive always had concerns about PIP. thanks again bro!
Photon
Member
Optional
bobmyer12541
New Member
got it dissolved bless bro! ill heat it up before injecting, should i expect a lump in my ass? super hyped to try injectable anadrol just never wanted to inject guaiacol. thanks again for responding.
Ive just attempted this.
30mg anadrol
1.5%BA
40% BB
Rest was GSO
Cooked it for 3 hours
Anadrol went in first all the BA and then half of the BB, heated until clear.
Poured GSO in But didnt let temps go below 75. Kept it steady.
After around a hour I did the rest of the BB and GSO slowly over the hour at 75. Then turned her up to 80.
I Immediately filtered (yes the filter doesnt like 80 degrees)
Once filtered i cold plunged the media in ice water for 45 mins to let it set and that temperature and allow the compound to be exposed to the two extremes in hope for stability at room.temps.
So far its held [24hours] no signs of crashing. Tried it as pre today and fark me it was a game changer. No lumps or redness. Just a sting. For a couple hours, mind you it went through a slin needle so maybe some compound floating in the extra cellular space. It feels like a clean version of anadrol. Love it.
Smooth, however it stung for a bit from the amount BB. No super solvents used.
Will report back in 24 hours to see if its crashed.
Also im new here. Been brewing for some time
keen to always learn more from people.
30mg anadrol
1.5%BA
40% BB
Rest was GSO
Cooked it for 3 hours
Anadrol went in first all the BA and then half of the BB, heated until clear.
Poured GSO in But didnt let temps go below 75. Kept it steady.
After around a hour I did the rest of the BB and GSO slowly over the hour at 75. Then turned her up to 80.
I Immediately filtered (yes the filter doesnt like 80 degrees)
Once filtered i cold plunged the media in ice water for 45 mins to let it set and that temperature and allow the compound to be exposed to the two extremes in hope for stability at room.temps.
So far its held [24hours] no signs of crashing. Tried it as pre today and fark me it was a game changer. No lumps or redness. Just a sting. For a couple hours, mind you it went through a slin needle so maybe some compound floating in the extra cellular space. It feels like a clean version of anadrol. Love it.
Smooth, however it stung for a bit from the amount BB. No super solvents used.
Will report back in 24 hours to see if its crashed.
Also im new here. Been brewing for some time
keen to always learn more from people.
Last edited:
