helionlabs
Subscriber
helionlabs@proton.me
Greetings Meso-Rx!
We are Helion Labs! While we may be new here we are not new to the public and have had our products on the dark web for a while as well as selling locally since 2019. Some of our customers include high level Bodybuilders, Powerlifters, Influencers and Strongmen. We also have been active in the Homebrew section helping out where we can.
Now onto the important stuff:
Procedures
Injectables Procedure
1. All raws are sent in to GetYourDrugsTested to confirm what the supplier sent was accurate. Any that do not pass are sent to Janoshik for further testing.
2. Lab area is sealed off and thoroughly cleaned and sterilized
3. Lab workers thoroughly wash hands, and put on a clean lab coat, new medical mask and medical gloves. Gloves are changed liberally during brewing process
4. Vials, glassware, dispenser and silicone stoppers are washed with detergent and tap water and rinsed off well before being placed in a bath of distilled water. They are transferred to another bath of distilled water after.
5. All of the above are placed in a pressure cooker at 15PSI for 30 minutes to sterilize.
6. The above is wrapped in sterilized aluminum foil and placed in an oven at 200f for 1 hour to dry. This oven is not used for any thing other than this.
7. Once glassware has cooled, the brewing process begins by mixing the carrier oil (Mig840) and solvent over a hot plate with a sterilized magnetic stir bar. Raws are mixed in next followed by a preservative.
8. Once mixed, it is then put through a glass vacuum filtration setup which uses a sterilized 0.22um PTFE or Nylon paper filter.
9. Filtered oil is then dispensed into vials using a pipette or dispenser under a laminar flow hood.
10. Using sterilized tweezers, stoppers are placed on to the vials.
11. Vials are crimped and labeled.
Capsules Procedure
1. All raws are sent in to GetYourDrugsTested to confirm what the supplier sent was accurate. Any that do not pass are sent to Janoshik for further testing.
2. Raws are mixed/geometrically diluted with creatine monohydrate and blue spirulina or red beetroot powder with a motor and pestle . A rubber spatula is also used to help thoroughly mix the powders.
3. Mixed powder is put into capsules via capsule machine.
4. Capsules are cleaned off with compressed air.
5. Capsules are counted via a capsule counter and placed into labeled mylar pouches.
6. Mylar pouches are sealed.
OpSec
Meso and emails are only viewed on a new computer through TOR. We also have a public PGP key in case you want to encrypt your messages. If you provide a public PGP key we will encrypt our messages to you.
Pricelist
View: https://pastebin.com/7H2qJt9D
You can also view it at helionlabs.net
We only accept Bitcoin (BTC) and Monero (XMR).
Although we strive to provide the best service and best products at affordable prices, please keep in mind that this is not our main focus so if things are not in stock but raws are, it might be a few days to get your order fulfilled. We will reinvest into more automation of the manufacturing process in order to shorten turnaround times as well as better labels, packaging and more tests from Janoshik.
Greetings Meso-Rx!
We are Helion Labs! While we may be new here we are not new to the public and have had our products on the dark web for a while as well as selling locally since 2019. Some of our customers include high level Bodybuilders, Powerlifters, Influencers and Strongmen. We also have been active in the Homebrew section helping out where we can.
Now onto the important stuff:
Procedures
Injectables Procedure
1. All raws are sent in to GetYourDrugsTested to confirm what the supplier sent was accurate. Any that do not pass are sent to Janoshik for further testing.
2. Lab area is sealed off and thoroughly cleaned and sterilized
3. Lab workers thoroughly wash hands, and put on a clean lab coat, new medical mask and medical gloves. Gloves are changed liberally during brewing process
4. Vials, glassware, dispenser and silicone stoppers are washed with detergent and tap water and rinsed off well before being placed in a bath of distilled water. They are transferred to another bath of distilled water after.
5. All of the above are placed in a pressure cooker at 15PSI for 30 minutes to sterilize.
6. The above is wrapped in sterilized aluminum foil and placed in an oven at 200f for 1 hour to dry. This oven is not used for any thing other than this.
7. Once glassware has cooled, the brewing process begins by mixing the carrier oil (Mig840) and solvent over a hot plate with a sterilized magnetic stir bar. Raws are mixed in next followed by a preservative.
8. Once mixed, it is then put through a glass vacuum filtration setup which uses a sterilized 0.22um PTFE or Nylon paper filter.
9. Filtered oil is then dispensed into vials using a pipette or dispenser under a laminar flow hood.
10. Using sterilized tweezers, stoppers are placed on to the vials.
11. Vials are crimped and labeled.
Capsules Procedure
1. All raws are sent in to GetYourDrugsTested to confirm what the supplier sent was accurate. Any that do not pass are sent to Janoshik for further testing.
2. Raws are mixed/geometrically diluted with creatine monohydrate and blue spirulina or red beetroot powder with a motor and pestle . A rubber spatula is also used to help thoroughly mix the powders.
3. Mixed powder is put into capsules via capsule machine.
4. Capsules are cleaned off with compressed air.
5. Capsules are counted via a capsule counter and placed into labeled mylar pouches.
6. Mylar pouches are sealed.
OpSec
Meso and emails are only viewed on a new computer through TOR. We also have a public PGP key in case you want to encrypt your messages. If you provide a public PGP key we will encrypt our messages to you.
Pricelist
View: https://pastebin.com/7H2qJt9D
You can also view it at helionlabs.net
We only accept Bitcoin (BTC) and Monero (XMR).
Although we strive to provide the best service and best products at affordable prices, please keep in mind that this is not our main focus so if things are not in stock but raws are, it might be a few days to get your order fulfilled. We will reinvest into more automation of the manufacturing process in order to shorten turnaround times as well as better labels, packaging and more tests from Janoshik.
Attachments
Last edited:
