Homebrewing Revalor-200 Troubles

[equalme]

So my first time trying out converting revalor-200 to tren ace and I'm running into a bit of trouble.

1.) I used heet to dissolve the crushed pellets (3 hours), then filtered through coffee filter.
2.) I poured in dissolved naoh (30mg since I was told 75mg per five cartridges and I only used two) and let it sit for 1 hour exactly.
3.) Ice cold distilled water and dripped for roughly 30 minutes (~400ml).
4.) Filtered through coffee filter and rinsed with a gallon and half of distilled water.
5.) Air dried for two days and used a card to chop up the powder.
6.) I weighed the dried powder and came out to almost exactly 3.5 gram (I used two cartridges which is a total of 4 grams).
7.) I mixed 1ml BA, 1ml EO, and 30ml GSO to get roughly 100mg/ml.
8.) Problem...the powder is not fully dissolving into the oil. I'm heating it (~225F for 30 minutes) and it still isn't dissolving.

Frustrating that I can't figure out what I did wrong...Any tips? Much appreciated!

 

[equalme]

I read that tren ace readily dissolves in BA/GSO without the use of either BB/EO so I barely used any EO.

 

[equalme]

Ok I just filtered it again through a coffee filter, scooped up the goop and poured in a good amount of EO and the goop still won't dissolve. Wtf...

 

[HuckingFuge]

I think that is wrong. add more EO. heating your Tren was a mistake. you probably left to much powder on the filter also.

 

[HuckingFuge]

were did you get the goop from?

 

[equalme]

I think that is wrong. add more EO. heating your Tren was a mistake. you probably left to much powder on the filter also.

I know heating is bad on tren as it oxidizes easily, but I had no choice but to try it.

I scraped off as much of the dried powder as possible. 85% yield is good enough for my expectations.

were did you get the goop from?

The dried tren ace powder was not dissolving after I mixed in BA/EO/GSO, so I just poured it through a coffee filter and I was left with the "tren ace powder" aka goop. I then scooped up the goop into a beaker and poured straight EO into it and it still isn't dissolving.

 

[HuckingFuge]

I don't think the goop is Tren. how big of a vial are you working with? how much EO did you add?

 

[equalme]

I don't think the goop is Tren. how big of a vial are you working with? how much EO did you add?

What else could it be then? The goop is a good tren yellow color. I added about 10ml of EO to the goop...but no way for me to measure the amount of goop so doesn't really matter then.

This is what it looked like after I added in BA/EO/GSO to the dried tren ace powder.

 

[HuckingFuge]

that looks like shit. I don't know why it went to goop. no matter what you did to the Tren it should of not done that.

 

[Notits]

Equal me, I agree with huck here, something fell apart here, what ever you do keep that shit away from your glutes!! But more importantly figure out what went wrong so you get closer to a successful brew. Where are you getting your instructions? Im currently reading into this a bit and may consider taking a shot at it myself. The only practical information i have been able to find is on basskillers website.

 

[equalme]

Equal me, I agree with huck here, something fell apart here, what ever you do keep that shit away from your glutes!! But more importantly figure out what went wrong so you get closer to a successful brew. Where are you getting your instructions? Im currently reading into this a bit and may consider taking a shot at it myself. The only practical information i have been able to find is on basskillers website.

After filtering the goop through the coffee filter it is pretty clear...so I went ahead and filtered it through a .2 syringe filter and ended up with this:

I followed basskillers synovex conversion exactly how it is guided. I can't really think of what went wrong...

 

[HuckingFuge]

now the test is to try it. I would taste it to see if it burns your tongue. were did the goop go?

 

[equalme]

How legit is the taste test? I'd assume the BA or EO would likely cause the burning sensation.

The goop is still sitting in the beaker in EO...still hasn't dissolved. Lol.

 

[HuckingFuge]

I'm worried about there being lye in your solution. I thought of lye when I saw the goop. if you have ph paper you can check and see how basic the end product is.

 

[equalme]

I'll see if I can find some ph paper tomorrow. The goop is a lot more than the amount of lye used.

 

[Notits]

I'm worried about there being lye in your solution. I thought of lye when I saw the goop. if you have ph paper you can check and see how basic the end product is.

This ^^^^
What you have "looks" like your going in the right direction.
Also, i may be mistaken but syno conversion i believe strips the ester as well as the estrogen. Maybe someone else can clarify. I think what you end up with is based/no ester.
No?

 

[HuckingFuge]

I'm probably just being paranoid. rather be safe than sorry.

 

[HuckingFuge]

This ^^^^
What you have "looks" like your going in the right direction.
Also, i may be mistaken but syno conversion i believe strips the ester as well as the estrogen. Maybe someone else can clarify. I think what you end up with is based/no ester.
No?

the ester doesn't get stripped, you still end up with Prop, cause if it did we would be screwed. to hard to get TNE into inject able form.

 

[equalme]

I'm going to order some synovex to practice on since it is a third of the cost of revalor until I can get this correct. Hate that I don't know what is wrong since it is so damn time consuming too! I appreciate all of your help.

 

[HuckingFuge]

good luck