Ok guys here goes. I have been home brewing for years. Good source etc. Only time i ever had problems was using to much ba. Anyways my last few batches have been shit. I inject 1 ml of test and i get swollen and painful and lumps that stays for 2 weeks. I thought at first to much ba. Then i made another batch of test ( always at 250 a mk) and made sure my ba was at 2 percent. same thing. so i dilluted it with oil to make 125 mg and it helped alot. But not completly. So i thought maybe it was the oil ( i had always used wesson oil) so i got some salflower oil and brewed up test at 250 ml and same problem. I dissolve in oil ( used to dissolve in 6 ml of bb before adding oil but that didnt help either) add 2 percent ba then filter thru whatmen put in 50 cc vial . i use 23 guage 1 inch for butt and 5/8 or sometimes 1 inch ( not all the way) for thighs. and sometimes a insulin syringe. rotate sites every week etc. makes my thighs so tight and painful i cant bend leg much. no fever or anything. just weird to me. and this either test e or sust 250. doesnt matter they both do it. thanks guys
MESO-Rx
Anabolic Steroids
lumps swelling and pain
- Thread starter imnotbigenuf
- Start date
TrennedOutLunatic
Banned
I hear that test e raws are problematic nowadays.
Why 23g though?
25 will do just fine.
I use full eo and pin with 27g
Why 23g though?
25 will do just fine.
I use full eo and pin with 27g
xgunx
Member
Was going to say the same. Especially older test E raws are causing pip. Also I only use 1% ba but kinda doubt that is your problem. Are you doing anything like reusing filters? Any other details you can provide will help. Walk us through. Unless you have test e that's either old or one of those batches people are complaining about.
xmilar
New Member
Sounds like a bad batch of raws of you ask me
basic brewing procedure. I put test and oil in a clean small jar with lid. if i use bb i put that in first then the oil) i let it sit for a day ( sometimes just do it that day after its all dissolved. ) if i need heat to dissolve i put pan on stove warm it up ( not boiling) put jar in for a few minutes. then i take it out get new needles insert into new vial . always making sure i have just washed my hands and used alcohol swabs on vial before inserting needles. put a new whatman syringe filter on needle in vial. i then draw out 3 cc at a time from jar and put into vial thru the whatman at slow rate. then when i have it full i will add the 2 percent of ba to mix.. I have noticed now if i dillute my mixture by half with oil ( from 250 mg a cc to 125 mg a cc its ok) i have tried adding more ba adding more bb and still the same . but if i just add more oil its ok ( at least when injecting 1/2 a cc) just to check it out. again only with my test e my test c and sust 250. i just brewed up some deca will try that in a few days to see if i get the same results. weird
Whopperflopper
Member
Am I the only one that puts the raw in the bb, and ba until disolved? You know, stir,heat, then add warm oil? I'm doing this all wrong. Help me. Test E has caused enough problems that I cant see why anyone would mess with it. I'd bet its stored in a leftover chicken shit bucket before being packaged. Damn Palodiumn
I don’t think it matters- seen guys do it both ways. Boiling point of BA is over 400 degrees F. Any other opinions on this?
TrennedOutLunatic
Banned
I just throw everything in a beaker and that's it.
HunterHowl
Member
Sounds like OP is not going deep enough on the thigh. 5/8 is usually for delt and depending on your weight and body fat. You may have to inject all the way in with 1 inch on your thigh. Or it could be a bad batch, dirty gear, or virgin muscles. I always prefer to use test Cypt instead of E after i got really bad infection from test E. You can alternate left to right glute for entire test E cycle.
HunterHowl
Member
Haha dont be so aggressive buddy. OP, Next time put your oil first and then add bb and ba. Put test powders last. Make sure to clean your Baker and stir rod with alcohol and then antibacterial soap. Heat up the baker for any excessive water.
*double filter" if you can. It never hurts to that
5/8 is plenty deep for muscular thighs. ive tried 1 inch too and same thing. ive hit delts and pecs with slin pins and still got the lump. this was with trying different ideas such as heating the batch in oven at 230 degrees etc. happens with both the sust 250 and test e. i havent tried the deca yet. going to try using a whole cc tonight ( dilluted in half 125 mg instead of 250 mg per ml) when i used 1/2 cc it was fine. dont make sense but if i have to do things that way i will cuz i dont want to waste 20 grams of product.
You do realize there was a ton of bad test e raw going around. Several sponsors were getting the same complains from customers. Seems that maybe the large batch of test e got compromised during storage or whatever. That’s why I was saying to try using a totally different carrier like GSO only or CSO at 200mg/ml. Inject 1.5 in x 25ga in glute. This eliminates all the questionable factors. If you get it after that then it’s bad raws.
xgunx
Member
To add co text to the bad batch of test e everyone has been getting some of.
After lots of reading I have found that many people say once test e gets old it develops pip. If a big batch reached that point for whatever reason, it could make a difference.
After lots of reading I have found that many people say once test e gets old it develops pip. If a big batch reached that point for whatever reason, it could make a difference.
