Mast P 200 Dropped out of Suspension

GENX-J

New Member
Hello, I Have 6 Vials of Primal MAST P 200 that dropped out of suspension, what is the best method to recover it? Thanks
 
This is normal and happens with mastP200. Use a coffee mug warmer to get it back into solution. Only do this one vial at a time for the one you plan to use. Once’s it’s back in solution consider keeping the vial you are using in a baby wipe warmer at 99-113F to keep it in solution (also warmer oil draws better and has less pip). Only do this if you plan to use the vial up within a month or 2
 
I used a coffee mug warmer which worked but the next day it was crystalized again. I usually load my syringe the night before with test, mast p, mast e and tren ace, I'm a little worried it would crystalize over night in the syringe. not sure what to do, I can't post in the Primal forum because I'm new.
 
I used a coffee mug warmer which worked but the next day it was crystalized again. I usually load my syringe the night before with test, mast p, mast e and tren ace, I'm a little worried it would crystalize over night in the syringe. not sure what to do, I can't post in the Primal forum because I'm new.
Were you able to put the mastP200 into a baby wipe warmer or something similar to keep it at around 100F once it was back into solution (after coffee mug warmer)? That usually works. Otherwise it def can crash again.
 
I don't have a baby wipe warmer, guess I'll have to get one, it's a shame I have 5 unopened vials Mast P 200 that have crashed
 
mine crashed also
-test p 200(primal)
-Mast p 200(primal

would boiling it work? I don't have a warmer
Boil water not the oil lol. Yes swirling the vial in boiled (removed from heat) water works but you need to be careful (use tongs or something) not to let the vial stopper come into contact with the water. Or, you could just buy a mug warmer (my suggestion).
 
I would think the only way to get it to stay un-crashed permenantly would be to add some BB. It might dilute it a little but you wouldn't have to keep warming it every time you go to inject.
 
What’s your diet and training like. I’m running 400 of each at 230 lbs and I’m seeing a lot of results

Training:
PPl split
low volume high intensity (2x failure)
6-8 sets per body part

Diet: Rebounded from a agressive cut really bad. Went from 8% all the way to like 18%

about 3000 calories right now 180 protein low fat
 
mine crashed also
-test p 200(primal)
-Mast p 200(primal

would boiling it work? I don't have a warmer
Not a good idea to put vials in water. You don't know how robust your vial is in regards to small leaks. Also at high temperatures you will have a lot of pressure building up. I have had vials explode the millisecond I touched them after heating them on the stove.

Use a heater or put the stove on the lowest setting and keep an eye on it, don't let it get so warm that you can't touch it. Put a needle in to release pressure too.
 
Sounds like you’re burned out from your cut ( I know the feeling). Best off cruising on TRT for 6 weeks at least and eat maintenance calories to let your body recover / acclimate to a new calorie base. Then slowly decrease calories by 10% assuming you want to cut from 18%. Wouldn’t bulk from there.
 
On one hand, I fell like taking over someone's thread is kind of a dbag thing to do. On the other hand, crashed gear is certainly something a search would have helped with, vendor notwithstanding... And we get a lot of the same threads already re: what do I do/no gains, etc.

i%27m-so-conflicted-katt-williams.gif
 
Back
Top