Npp Brew

[Bradybomb]

With my insulin syringes i can swap needle... i used 18g to draw and then pinned with the original one

View attachment 132703

I don’t think that is an insulin syringe, just a 1cc syringe. I wouldn’t use those for insulin or peptides because a few units will be left in the larger needle tip and may give you too much insulin. I do like using those 1cc syringes and switching the needles for gear like you though.

 

[Bradybomb]

How can be possible that ester change the properties of the molecule of AAS? how can you measure melting point of an esterified steroid? I mean the melting point of the Steroid, not of the complex Steroid + Ester. Boldenone Undecylenate is liquid at room temperature because of the undecylenic acid, but the Boldenon molecule should be the same of that one bonded to Cypionic ester... i mean the properties of steroidal ring not the whole new molecule Steroid + Ester, since i care about the unerestified molecule of the AAS the will bond to androgen receptors once ester bond is broken. So if i read that melting point of a unesterified steroid is 80 C, i will stay below and i dont care about ester melting point, as stated Equipoise is liquid at room temperature because of the undecylenic acid

I brewed Trenbolone Acetate Many times and going over 60 C changed its structure since the colour changed, and if the colour changed is because the whole structure changed, and reflex light differently. And guess, the dark orange tren didnt give me effects, like tren cough, sweats, nothing.

Anyway thanks for your answer regards Winstrol

Why does melting point mater so much? When it melts do you thing it degrades the hormone? I hear of some people heating TNE to its melting point without any solvents when they are starting it’s brew.

 

[FR0Z3N_B0MB3RRR]

I dont know, i m pretty sure that once a steroid hits its melting point it s damaged, but im talking about melting point, not solubilization. As already stated, Equipoise has a Boldenone Molecule bonded to the liquid undecylenic acid, but this doesnt mean the Boldenone steroid molecule has reached its melting point, i think is just “solubilized” into its ester that’s pretty big.
When you dissolve your powder into solvent at maybe 50 C, youre far from most common steroid melting points, again, Nandrolone Decanoate and Test Enanthate can melt at near 40 C , but because their ester does, the Nandrolone melting point is higher. Dont forget that when the esterase enzyme finishes to cut the ester’s atoms and set the steroid free, it has the same structure of that raw unesterified one you can have.

i dont know about tne without solvents that reach melting point. I just stay away from rediculously high temperatures. I needed to go over 50 C just for Anadrol Winstrol and Dianabol, 140 C for 30 minutes at 25mg/ml with 1% BA and 20% BB... and it s some months that’s running trough a slin pin..

 

[eery]

Yes but using insulin syringe. Or else i would absolutly do that.

if i have to ill just get 3 cc. I just like the 1 cc. Easy to use and store away. And doing ed injections at .5 cc. A 3 cc barrel seems like a waste

draw up 3cc, swap needldes and pin 1cc ED and redraw a new syringe every 4 days. Problem solved.

This is considering your gear isnt made with EO or guiacol as that might dissolve the stopper in that amount of time.

 

[jJjburton]

draw up 3cc, swap needldes and pin 1cc ED and redraw a new syringe every 4 days. Problem solved.

This is considering your gear isnt made with EO or guiacol as that might dissolve the stopper in that amount of time.

Ehh, is this ok? I feel like this would be bad because oil will eat at the rubber plunger. Even though its a short time. But i see what your saying.

 

[CApump]

Ehh, is this ok? I feel like this would be bad because oil will eat at the rubber plunger. Even though its a short time. But i see what your saying.

Better yet is drawing up 4 days worth of oil into a 3 cc pin and just using that to back load a slin pin for your ED pins. Just keep an air bubble between the oil and the rubber on the plunger and you won’t have any issues.