Mastedon
Member
I've spent too much time looking for 27g 1", but yes odd indeed....I use the Exel 28ga thin wall 3/4" when I need something longer than 30g 0.5" Nipro but sorter than 27g 1.25" Nipro.
MESO-Rx
Anabolic Steroids
OEP LABS Domestic
- Thread starter OEP LABS
- Start date
OEP LABS
Subscriber
Pardon my short absence, yessir that is me, email is correct 100%.
In regards to @loganmiller530 concern I’m all for blind testing 100%. Everyone that has done always paid back on the spot.
I encourage it.
OEP LABS
Subscriber
Couple Announcements Topics: Current Schedule and Future Schedule
As always Men we’ll cut straight to the topics without the pleasantries. As most who have been following the thread, are fully aware of the current protocol. However, as more join us whether it be from other platforms or here, they may have questions on these procedures or what’s the most current update. I’ll be utilizing the Pastebin to provide these updates. As of right now current schedule is picking up Inventory in regards to compounds that have a purity report or a purity report that we currently received.
Future Schedule.
While I can’t speak on the details of 5 samples with the 3 Laboratories, they are blind samples.
I can speak on what has been fired off, TRA 1, TRA 2, Deca 1 , Deca 2 and Halo, susta-lube duplicate. These are the latter part of all the samples so progress is indeed happening. I understand the wait is frustrating, however the reports will tell us if the material is even deemed useable. Second, Everyone works hard around here, we expect purity to be quality at least usable not material from the garbage. Third of all, I utilize the report to correctly synthesize the material to have the correct HPLC target Report. More Pastebin updates to come, I’ll be checking in periodically Men thank you for your time.
As always Men we’ll cut straight to the topics without the pleasantries. As most who have been following the thread, are fully aware of the current protocol. However, as more join us whether it be from other platforms or here, they may have questions on these procedures or what’s the most current update. I’ll be utilizing the Pastebin to provide these updates. As of right now current schedule is picking up Inventory in regards to compounds that have a purity report or a purity report that we currently received.
Future Schedule.
While I can’t speak on the details of 5 samples with the 3 Laboratories, they are blind samples.
I can speak on what has been fired off, TRA 1, TRA 2, Deca 1 , Deca 2 and Halo, susta-lube duplicate. These are the latter part of all the samples so progress is indeed happening. I understand the wait is frustrating, however the reports will tell us if the material is even deemed useable. Second, Everyone works hard around here, we expect purity to be quality at least usable not material from the garbage. Third of all, I utilize the report to correctly synthesize the material to have the correct HPLC target Report. More Pastebin updates to come, I’ll be checking in periodically Men thank you for your time.
Inkniron87
Member
No rush my man you’re doing it the right way. Will be ready when you are regardless
OEP LABS
Subscriber
Thank you my dude.
This is your non-formal Pench. For those that read 12 samples in the previous, yes that still holds true even the post on this page shows 5 compilations. Why.
I’m going to going to tell you why.
The other samples are finished oils checking early hplc targets before even put out. You tend to learn fast after the experience with Test Cyp Gso. If there is opportunity to check, in my opinion why take advantage of it. Maybe overkill but I never built a Race Car to lose.
Edit. Complications. Should read compounds.
Rido
Subscriber
AllbrandNew
Member
Subscribed.
AlexDavis43
Member
OEP LABS
Subscriber
My Man! lolZ! Reminds me of the Phk It I'll Pin Blend for some reason.
I've updated the list, that way everyone can see where the workload is at. What samples have been tested and those in que, so fourth.
If time allows I will gather all the testing and update it, into the current pastebin. That way everyone can see what materials are being put in to work.
I say time allows since Currently sterilizing glass in the sealed filter room, been locked down for awhile. Not crazy yet though, while that was confirmed a long time ago. Please allow me to post the link as new members and also Vets have inquired about Men.
View: https://pastebin.com/DBcEeViJ
AlexDavis43
Member
I mean, realistically, are you looking to hire an intern yet?
the important part: there are companies you can hire to take care of all the paperwork to get them on a State-funded paycheck while you get an extra pair of hands in the lab and a tax write-off
Andrewthatguy
Member
Please bring back the phuck it I’ll pin it blend lmao
OEP LABS
Subscriber
Was joking my man on the crazy. To address your concern
It has been an ongoing thought, however this shop from start was geared more of a Boutique style In mind. Those old school sayings tend to replay in my mind being asked this. “If it’s not broken don’t fix it,” or “if you want something done right do, do it yourself.” I understand the urge of wanting an item right away in hindsight I’ve realized it’s also less stressful engaging with clients that are patient. I understand both sides. That’s is why the money back refund is always at your discretion if you every feel you are waiting too long, its there 100%. I will keep your request in mind as it’s never a no.
OEP LABS
Subscriber
Perhaps pics can do a better justice rather than me explaining in regards to quality over quantity. Upgrades that have been made to avoid leeching as higher concentrations compounds are being used.
Staying away from polystyrene at all costs.
Sterile Whatman filters in polypropylene housings, upgrading all joint fittings, valves, gauges everything to 316L
Upgrading main Line to PTFE inner coated stainless 316L. Doing the best we can. Attached. I’ll stop my rambling back to work
Staying away from polystyrene at all costs.
Sterile Whatman filters in polypropylene housings, upgrading all joint fittings, valves, gauges everything to 316L
Upgrading main Line to PTFE inner coated stainless 316L. Doing the best we can. Attached. I’ll stop my rambling back to work
Attachments
OEP LABS
Subscriber
@DraxTheDestroyer in regards to pip per our last open convo here. There are options. You can pm or email whichever is most convenient for you sir. Per the correct etiquette its best I await your message sir.
Similar threads
