Oil just leaking back out of injection site...Help

[JonTest]

Okay ever since i started my cycle, which was two weeks ago, everytime i inject a little bit of oil comes out of the injection site......
Well about 5 minutes ago I injected two mL of gear and a whole SHITLOAD came back out........What exactly causes this and how can i stop it...............Thanks

 

[JonTest]

Oh yeah BTW.....Tren acetate KICKS ASS............later

 

[gman67]

Are you injecting slowly and what length pin are you using??

 

[JonTest]

actually this time i know injected fast.......And it was a 23gauge 1 inch pin............

 

[gman67]

actually this time i know injected fast.......And it was a 23gauge 1 inch pin............

I always make sure to inject slowly, that's why I use a 25g,,you'll never go too fast with that lol,,having just a drop of oil at the injection site is common,,that can be from the oil on the outside of the needle itself.

 

[Cronk]

Yep, tren is the shit. I can't go over 100mg ED or I get too irritable. Now, as for the oil seeping out, you only need to apply pressure and massage the deposited oil into the muscle. This will prevent it from seeping back out through the needle track. Some people like to z-track the injection site by pulling the skin to any direction before inserting the needle. The oil is deposited, the needle is removed and the skin is let go to slide over the muscle. This sometimes helps by causing the door to close on the needle hole. Myself, I just apply pressure and massage for awhile. Hope this helps.

Cronk

 

[eleven11]

same here love 25g. also before you inject slide the skin up a little of course this only works on legs and glutes, that way after you release the skin it will cover the injection hole. also inject real slow and then wait a few sec. before pulling the needle out. hope this helps...........11

 

[JonTest]

thanks fellas

 

[DoiMiNioN]

If that all fails.. i suggest licking it off

 

[thefallguy]

Yep, tren is the shit. I can't go over 100mg ED or I get too irritable. Now, as for the oil seeping out, you only need to apply pressure and massage the deposited oil into the muscle. This will prevent it from seeping back out through the needle track. Some people like to z-track the injection site by pulling the skin to any direction before inserting the needle. The oil is deposited, the needle is removed and the skin is let go to slide over the muscle. This sometimes helps by causing the door to close on the needle hole. Myself, I just apply pressure and massage for awhile. Hope this helps.

Cronk

Cronk beat me to it........go z-track.

 

[JonTest]

If that all fails.. i suggest licking it off

oh i do that anyways......

 

[brady_hilltop]

i always make sure i stick it @ least an inch, shood it slow, and don't immediatly pull the dart out....that's when i get it seeping back out...if i wait a few seconds, 5-15, then pull out don't get so much maybe a drop or two

just my .02

 

[ramboj70]

i always make sure i stick it @ least an inch, shood it slow, and don't immediatly pull the dart out....that's when i get it seeping back out...if i wait a few seconds, 5-15, then pull out don't get so much maybe a drop or two

just my .02

ditto

 

[Pup'nIrn]

Plug that SOB before you lose your gear! A leaky ass is not sexy! LOL

 

[Colossus]

Depending on where you are injecting can help you determine the size of needle you need to use. You need to get deep into the muscle tissue so using an inch needle in your glute, especially after having to go through some fat, will cause some oil leakage. Injecting into the shoulder may only require an inch needle. My suggestion, use an 1 1/2 inch pin for larger muscle groups like your glute and an inch pin for smaller.

Be Safe

 

[roofer]

i aways wait at least 10 seconds before i pull the needle out.