PIP Free Glutathione

[HereToTeachAndLearn]

I finally figured out a PIP free glutathione recipe. The key was using 2% lidocaine injection liquid to replace BAC water in half of the final volume.

My example:

30ml total
200mg/ml

15ml 2% lidocaine injection liquid
6.3g reduced glutathione raw (5% overage)
2% BA (0.6ml)

Heated to 60C and stirred for about 30 minutes. Was very white and cloudy.

Slowly added NaOH pellets until it turned clear. Very little needed.

Once clear I added enough BAC water to make 30ml total. I believe it was something like 8-9ml.

Filtered into a 30ml vial and injected into quad.

ZERO discomfort and ZERO PIP after 3 consecutive days of injections.

If you want information on how to source low cost Pharma Lidocaine and BAC water, PM me and I will let you know how I purchased.

 

[Lil_swole87]

Interesting could you hit me up

 

[micro2000]

I finally figured out a PIP free glutathione recipe. The key was using 2% lidocaine injection liquid to replace BAC water in half of the final volume.

My example:

30ml total
200mg/ml

15ml 2% lidocaine injection liquid
6.3g reduced glutathione raw (5% overage)
2% BA (0.6ml)

Heated to 60C and stirred for about 30 minutes. Was very white and cloudy.

Slowly added NaOH pellets until it turned clear. Very little needed.

Once clear I added enough BAC water to make 30ml total. I believe it was something like 8-9ml.

Filtered into a 30ml vial and injected into quad.

ZERO discomfort and ZERO PIP after 3 consecutive days of injections.

If you want information on how to source low cost Pharma Lidocaine and BAC water, PM me and I will let you know how I purchased.

Did you test the pH to make sure you're not too alkaline after adding the NaOH?

 

[HereToTeachAndLearn]

Did you test the pH to make sure you're not too alkaline after adding the NaOH?

pH was about a 5 prior to adding NaOH. Ended up at about a 6.

 

[iris]

I finally figured out a PIP free glutathione recipe. The key was using 2% lidocaine injection liquid to replace BAC water in half of the final volume.

My example:

30ml total
200mg/ml

15ml 2% lidocaine injection liquid
6.3g reduced glutathione raw (5% overage)
2% BA (0.6ml)

Heated to 60C and stirred for about 30 minutes. Was very white and cloudy.

Slowly added NaOH pellets until it turned clear. Very little needed.

Once clear I added enough BAC water to make 30ml total. I believe it was something like 8-9ml.

Filtered into a 30ml vial and injected into quad.

ZERO discomfort and ZERO PIP after 3 consecutive days of injections.

If you want information on how to source low cost Pharma Lidocaine and BAC water, PM me and I will let you know how I purchased.

In my neck of the woods, a iv or injection of glutathione is more than 100gbp. Mg/ml vary a lot, though. This is cool

 

[Lifting88]

Can you send me a pm where to buy the Pharma Lidocaine

 

[IronGrip]

Could you pm about how cheap your BAC water source is

 

[HereToTeachAndLearn]

Water Bacteriostatic IV Inj Sol MDV 30mL Sterile FTV 25/Pack

MedexSupply.Com offers you a hassle-free shopping experience, with competitive prices, fast shipping, and friendly knowledgeable service!

medexsupply.com

 

[magRT496]

pH was about a 5 prior to adding NaOH. Ended up at about a 6.

Prob a dumb question but what do you use to measure Ph?

Also can you PM where to get the Lidocaine? I didnt see 2% on the link above

 

[Ghoul]

Just filter it. .2u will allow it to pass and take care of pip.

 

[Kiraa710]

-7.53 Raw In

-0.35mL BA

-Distilled Water

-PHd with NaOH to 5.5ph

pip free taking 2mL EOD

 

[Ghoul]

-7.53 Raw In

-0.35mL BA

-Distilled Water

-PHd with NaOH to 5.5ph

pip free taking 2mL EOD

You're injecting plain distilled water?

 

[Kiraa710]

You're injecting plain distilled water?

With the 7.53g of raw and 0.35mL of BA, thought you’d know a recipe when you see one man cmon now

 

[Ghoul]

With the 7.53g of raw and 0.35mL of BA, thought you’d know a recipe when you see one man cmon now

Most people reading this won't know distilled water from the supermarket isn't the same as "sterile water for injection".

 

[Kiraa710]

I refer to that as “Natural Selection”

Most people reading this won't know distilled water from the supermarket isn't the same as "sterile water for injection".

 

[legacylogisticsint]

I finally figured out a PIP free glutathione recipe. The key was using 2% lidocaine injection liquid to replace BAC water in half of the final volume.

My example:

30ml total
200mg/ml

15ml 2% lidocaine injection liquid
6.3g reduced glutathione raw (5% overage)
2% BA (0.6ml)

Heated to 60C and stirred for about 30 minutes. Was very white and cloudy.

Slowly added NaOH pellets until it turned clear. Very little needed.

Once clear I added enough BAC water to make 30ml total. I believe it was something like 8-9ml.

Filtered into a 30ml vial and injected into quad.

ZERO discomfort and ZERO PIP after 3 consecutive days of injections.

If you want information on how to source low cost Pharma Lidocaine and BAC water, PM me and I will let you know how I purchased.

can u send me a PM with info please thank you!

 

[kain]

can u send me a PM with info please thank you!

You can get bac and lidocaine from Medex.

 

[HereToTeachAndLearn]

can u send me a PM with info please thank you!

Water Bacteriostatic IV Inj Sol MDV 30mL Sterile FTV 25/Pack

MedexSupply.Com offers you a hassle-free shopping experience, with competitive prices, fast shipping, and friendly knowledgeable service!

medexsupply.com

 

[vulpinis]

Just filter it. .2u will allow it to pass and take care of pip.

is a.2u hydrophilic pvdf filter ok for this job? I've only handled oils to date. I would think if its heated you would want pvdf vs nylon.

 

[Ghoul]

is a.2u hydrophilic pvdf filter ok for this job? I've only handled oils to date. I would think if its heated you would want pvdf vs nylon.

PVDF will work, but PES is preferred because less Glutathione will stick to it and it has higher flow. Both are considered low-binding though, so you can use PVDF hydrophilic filters if that's what you have on hand, with just a small amount of loss.

PES can withstand 200c.

Definately don't want nylon.