Kpaxi
Member
Alright so let’s add vac pump and filter. No syringe filter. Went ahead and bought it so my little lab is complete.
MESO-Rx
Anabolic Steroids
Pre Brew Settup
- Thread starter Kpaxi
- Start date
You bought the vac?
Any thought on this? Too big?
Kpaxi
Member
Yea I bought the vac. I’m going with disposables since it’s cheaper. If you get the ones like that all you gotta do is buy the filters so it’s cheaper long run. I like your style tho
RCCP
Member
Over kill, but will work just as well. Two stage just means it wills be easier for the pump to pull a strongers vacuum. one cylinder pumps, sends it to the second cylinder and pumps some more.
55USD on the bay.
85-2 MAGNETIC STIRRER WITH HEATING PLATE
also on the bay, cheap Chinese or search daily for used commercial models. Also look up dental sterilizer on the prime site, there are some for cheap. Dry needs to get up to 325degee. just make sure the smaller dental ones are big enough to fit what you need.
Why would you wants to inject something in your body that's not as clean as possible, your personal lab should be cleaner and better sets up than any UGL. The cost savings isn't from skipping on equipment it comes from assuming the risk for making AAS
Multiple, one cup/filter one brew. Those filters are attached and you also need the bottle to put it in, the company should have it or any GL45 glass media bottle will do.
If you want to change just the filter for $1 then get the flask setup mich is showing, the bay has cheap ones for 50USD or so. but now you need to clean and sanitize the flask and glass funnel.
Kpaxi
Member
In that case I’ll go with the glass. I know I need whatman filters 20-25 microns if I’m not mistaken. Do these need to be nylon as well?
RCCP
Member
0.2 micron ZERO POINT TWO!!! you're filtering to actually physically remove bacteria. not 20 or 25. Not .45 either the .22/.20 is the minimum. The vast majority of bacteria and a lot of the virus are bigger than 0.2 so filtering down to that gets pretty much all bacteria you'd have to worry about.
Just to make peoples paranoids. Filters only catch 98% or 99% or so of something at the rated size. So not only are there bacterias and virus smaller than the .22 we filter to the filters aren't even ever 100%.
Nylon, PVDF, or PTFE are acceptable. Do not use PES, no MANUFACTUR recommends PES for use with BA. yes bros will say they use it or it's only 2% BA but again, it your body what do you want to inject in it? I'll listen to the company who engineers the filter before a bro.
Just to make peoples paranoids. Filters only catch 98% or 99% or so of something at the rated size. So not only are there bacterias and virus smaller than the .22 we filter to the filters aren't even ever 100%.
Nylon, PVDF, or PTFE are acceptable. Do not use PES, no MANUFACTUR recommends PES for use with BA. yes bros will say they use it or it's only 2% BA but again, it your body what do you want to inject in it? I'll listen to the company who engineers the filter before a bro.
I was checking this one out on eBay but am wondering what is the maximum temperature this hot plate/stirrer can reach.
I’ve read many times that the heat is not as used, since the solvent is supposed to do the work.
If you had to use so much heat to dissolve, it could re-crystallize once cool again?
I don’t brew yet- I’m just taking notes
If you had to use so much heat to dissolve, it could re-crystallize once cool again?
I don’t brew yet- I’m just taking notes
picholas
New Member
Didn't see what you got but hope it wasn't this. This is a PES filter.
Kpaxi
Member
No I switched it and ended up getting 13mm nylons lol. Waiting on the bigger nylons to come in now
RCCP
Member
Not sure the reviews are spotty but for 1/4 the price of others it may be worth a risk.
for the most parts, this is what I understand as well. I've also read that TestE contains carbonic acid or something as part of the manufacture process and boiling it off at 180 degree reduces PIP.
Kpaxi
Member
I didn’t heat my test P or Tren A and it came out perfect
