Primo Pip

[BamaCrazy]

No I feel fine it just hard asf

Yep. That’s the infamous GA Primo knot.

 

[bananafeet]

I injected 0.6ml of Tracy's primo 200mg/ml in my right glute. Literal golf ball sized lump/knot that lasted for 7 days. You could see the muscle belly pop out. No redness or heat. Yes I had refiltered it, no it wasn't crashed. Yes I injected it slowly with a 25G 1" needle.

Not keen on running primo again and wondering why this compound is so hyped.

 

[ve79]

Yep. That’s the infamous GA Primo knot.

Well in least it's real but fuck it hurts

 

[BamaCrazy]

Well in least it's real but fuck it hurts

Depending on injection site I’ve had the knots last 7-14 days. Longer if you don’t ice it.

 

[cousinmuscles]

I have been using 2/20 ba/bb and straight EO for years. Test E, mast E, test D, nandrolone D, I can barely tell I injected anything. I don't do so well with MCT oil. Test prop is worse than this primo E however after 2 months now I am throwing in the towel, it seems my quads are giving in. Now I am upping the dose too so no point trying to live with this.

Relevant tip in this thread is start low first and then increase concentrations for brewers.

Update
I first brewed primo E at 200mg/ml, 2% BA, 20% BB, EO only, and injected 75mg test 60mg primo daily for the first 8 weeks.

I didn't manage to do all 8 weeks due to severe PIP, even fever. I then titrated and refiltered the primo to 125mg/ml. I also found that despite diluting it, my quads can't tolerate primo, I get a fever. So now I rotate between glutes, lats, chest and shoulders. In my second 8 weeks of this cycle injecting 100mg test E and 100mg primo E daily and there is a little PIP and a small lump lingering but it is no big deal.

 

[ve79]

Update
I first brewed primo E at 200mg/ml, 2% BA, 20% BB, EO only, and injected 75mg test 60mg primo daily for the first 8 weeks.

I didn't manage to do all 8 weeks due to severe PIP, even fever. I then titrated and refiltered the primo to 125mg/ml. I also found that despite diluting it, my quads can't tolerate primo, I get a fever. So now I rotate between glutes, lats, chest and shoulders. In my second 8 weeks of this cycle injecting 100mg test E and 100mg primo E daily and there is a little PIP and a small lump lingering but it is no big deal.

For me I learned it's the injection spots and splitting it in 2 has been working well only just a little soreness

 

[cousinmuscles]

For me I learned it's the injection spots and splitting it in 2 has been working well only just a little soreness

Yeah right now I am injecting 0.5ml test and 0.8ml primo, I mix it in a 10ml syringe and backfill slin pins at 0.65ml and pop two slin pins every morning, one in each glute, then lat, chest, delt, and then repeat. The PIP is not enough to make me feel anything during training.

 

[ve79]

Yeah right now I am injecting 0.5ml test and 0.8ml primo, I mix it in a 10ml syringe and backfill slin pins at 0.65ml and pop two slin pins every morning, one in each glute, then lat, chest, delt, and then repeat. The PIP is not enough to make me feel anything during training.

The chest and quads are the worst for me I don't even try anymore

 

[Fizzik]

QSC primo has been killing me. I put .6ML along with about .9ML of other oil(cyp and prop) in my left ventral glute a couple weeks back. PIP so bad I couldn’t put weight on my leg. Finally took dexamethasone to knock it down as sometimes it can linger for a week. I’ve had issues with that particular site in the past, so, I’ll no longer use it. Been fine in glutes, relatively ok in quads, as much as I try to avoid using them. Resorted to the use of a mug warmer, seems to have made something of a difference. I’d avoid that site for awhile. I think some QSC 200mg/ml batches are overdosed, which is likely the cause, Tracy denied the use of super solvents.

What temp is your mug warmer?

 

[ve79]

What temp is your mug warmer?

 

[ve79]

I've been running primo for a month with test and the results are fantastic but the knots and pips suck but I ice the injection spots and it has been working

 

[Bumpygooch]

No idea, it was $8, but, the oil is hot to the touch

 

[lilhawk]

I guess people have different reactions to compounds but I have never had pain from UGL primo or Bayer amps dosed at 100mg/ml. Used some that was 200mg/ml before and it never hurt either. I would say don't use primo that is a higher concentration than 100mg/ml, and/or find a lab that knows what they're doing.

 

[Prince Charming]

@Fizzik
I’ve been heating mine up at 130deg for between 10 to 5 minutes depending on how full the vial is. Start at 10min for a full vial and reduce time as vial gets lower. Like @Bumpygooch said pretty much until it’s hot to the touch.

 

[MrTexas2]

I have not read everything, but my simple solution (using 200 mg primo) is to mix it 50/50 with test.

The 110 mg I brewed was pipless.

 

[Ateam2023]

Depending on injection site I’ve had the knots last 7-14 days. Longer if you don’t ice it.

i have some primo e 200 from a couple years ago , im still hesitant to even give it a go because of all these pip knot stories,

 

[BamaCrazy]

i have some primo e 200 from a couple years ago , im still hesitant to even give it a go because of all these pip knot stories,

I can put up with almost anything. I can deal with the pain and the knots. But when I found out it’s spiking my CRP the entire cycle that changed things. I love Primo. But I’m not sure I’ll use it again.

 

[AlexDavis43]

i have some primo e 200 from a couple years ago , im still hesitant to even give it a go because of all these pip knot stories,

Could try diluting it &/or testing out a low volume injection

 

[BamaCrazy]

Could try diluting it &/or testing out a low volume injection

Primo 100 didn’t give me pip. But running 400-600mg of Primo a week using Primo 100 is not fun.