stupidly/lazily overdosed - crashing!

[T_verde77]

With some compounds like tren, I use no heat what so ever. I mix the BA and BB add the raw, cover and leave in the cupboard. After a few hours the raw is totally dissolved. A quick stir into the carrier oil then filter.

Works a charm. Never have to worry about damaging the hormone (bro science) but I like to be safe

I mean the tren has always still worked great for me, but why risk destroying it. I didn't even think they would dissolve without heat. sometimes it takes forever !!

 

[XKawN]

I use 1% ba. Couple things to keep in mind. The heat it would take to affect the compounds are in the high 100's per compound. And to evaporate ba would be in the mid or close to mid 100's. Can't remember exact per compound. So heating your sample to approx 250f would have no Ill effect.

 

[caveman72]

Hi folks,

Quick question for someone more intelligent than me please.. I overdosed some test-c (2% & 20% in cottonseed oil) whilst trying to use up what was left in the freezer.

Its 330mg/ml and it keeps crashing.. Am I ok/will it work to dilute it further with BB until it holds?

its a known fact test c is best at 200 to 250 no more
youj will not see test c over250.
if you haven't already add enough percentage of every thing like toy was making it 200 mg.add bb. make sure oil is added as well.

 

[Big_paul]

Hi folks,

Quick question for someone more intelligent than me please.. I overdosed some test-c (2% & 20% in cottonseed oil) whilst trying to use up what was left in the freezer.

Its 330mg/ml and it keeps crashing.. Am I ok/will it work to dilute it further with BB until it holds?

And it is going to keep on crashing. I used 18% bb and 1.5% ba for a 220 mg/ml solution of test cyp in 100 ml vials. It crashed so I added 2 more ml bb and 1 ml of ba and no more problems. You have 330 mg/ml. Say if you have a 20 ml vial you will need to break it up into 2 15ml vials. Add a small amount of bb at 1/10ml at a time until it stays in solution then top of to 15ml of carrier on each vial. You will need to re filter it also. You should be okay at around 20-22% bb.

 

[Big_paul]

Don't use cyp anymore. It takes as much solvent to dissolve as prop. For a 220 mg/ml solution you will need around 22% bb.

PM if you need to.

 

[Smoggybowman]

Thanks for the replies.. I made 300ml in 50ml vials.. I have a couple spare so I'm going to heat the ones that have crashed (oddly not all of them) and remove enough to bring the hormone down to what would be 250mg/ml over 50ml.

So I'll have 3x13.5ml in a separate vial to dilute down to 250mg and hopefully all will be right from there.

Lesson learnt, I won't assume things cook the same because they are similar again!

 

[ROOSTA]

I've done 200, 250, and 300 mg/ml test cyp with no issues except the day I left them out in the car during winter.

300test c.....and it didn't crash

 

[Andyboro]

300test c.....and it didn't crash

i made 300ml.. 150ml is fine, the other 150 turned to sludge! all from the same beaker, heated in the same way and from the same batch of raws. . go figure!

 

[ROOSTA]

i made 300ml.. 150ml is fine, the other 150 turned to sludge! all from the same beaker, heated in the same way and from the same batch of raws. . go figure!

Really....what raw source

 

[Smoggybowman]

Really....what raw source

The raws came from a UK based UGL.