Tailor
New Member
I would like to make test base without super solvents. I have found this recipe:
50mg/ml
BA 1%
BB 24%
GSO
Anyone tried this?
50mg/ml
BA 1%
BB 24%
GSO
Anyone tried this?
MESO-Rx
Anabolic Steroids
Megadick3000
Well-known Member
Cant say i have. But can i recommend something that uses just water as the solvent?
thinksteroids.com
Post #4 is the winning ticket.
Cyclodextrin encapsulation of testosterone base - any help?
So i got hydroxypropyl beta cyclodextrin, and testosterone base powder. Today i tried to encapsulate the testosterone. I dont think it worked. I followed exactly this procedure Homebrewing with beta cyclodextrins | JuicedMuscle.com Using 10g of HPBCD for 1g of test base. When i initially...
thinksteroids.com
Post #4 is the winning ticket.
DO NOT use gso for base steroids or your shit will crash! Use a good MCT oil and 2/30 is where I would start for 50mg/ml.
Tailor
New Member
Yea, mct for sure. What is the step by step brewing guide? Some ppl saying to heat up solvents and then add powder? What about carrier oil?
What concentration are you looking to brew? I've mostly read about people brewing 50mg/ml seen some do up to 75mg/ml with EO but they said it hurts.
Tailor
New Member
50mg/ml - MCT, BB and BA only. All about pip free.
Shouldn't be a problem but I think it will still hurt. Are you going to take it as a pre-workout or are you just trying to avoid drugtest?
Tailor
New Member
pre workout.
I was thinking about test suspension but heard about bad pip.
I was thinking about test suspension but heard about bad pip.
Make a small batch and try it. Some people say that test prop hurts, I've never had that crippling pain from test prop, always been like using cyp or enanthate. So I think it's the same with pure test base. But going up 75mg/ml with EO for sure hurts because I know some people that tried it and they sold their gear because it hurt so bad
Tailor
New Member
Do you think BA1% BB24% should work for 50mg/ml?
No Gods No Masters
Banned
I've brewed Test Base with no supersolvents.
However I used Mig840 and I dropped it down to 40mg/ml.
I've tried 50mg/ml with 30% BB, 1% BA with GSO and eventually it started falling out of suspension, it crashed very slowly over a series of days, just one crystal at a time.
Of course you can put it in 5ml vials and warm it with a coffee cup warmer each time to resuspend the hormone, let it cool and inject.
I prefer more oil and less hormone when it comes to Test Base to help with any pip.
For future reference order some Test Ace, it's the shortest ester, you can do GSO at about 80mg/ml, and it has absolutely no pip at all. Next time you place a raw order pick up this stuff as it's my favorite short ester, I prefer it over test base.
However I used Mig840 and I dropped it down to 40mg/ml.
I've tried 50mg/ml with 30% BB, 1% BA with GSO and eventually it started falling out of suspension, it crashed very slowly over a series of days, just one crystal at a time.
Of course you can put it in 5ml vials and warm it with a coffee cup warmer each time to resuspend the hormone, let it cool and inject.
I prefer more oil and less hormone when it comes to Test Base to help with any pip.
For future reference order some Test Ace, it's the shortest ester, you can do GSO at about 80mg/ml, and it has absolutely no pip at all. Next time you place a raw order pick up this stuff as it's my favorite short ester, I prefer it over test base.
Tailor
New Member
Does test ace have the same blast as test base? I would say it will be in between base and prop?
Did you try to brew any suspension? Test base or winny?
Nearly forgot to ask about guidance for brewing tne. Many people advise to heat up solvents and oil separately. Then to solvents and on powder, once dissolved add on oil. Basically keep temp high when brewing all the time.
Did you try to brew any suspension? Test base or winny?
Nearly forgot to ask about guidance for brewing tne. Many people advise to heat up solvents and oil separately. Then to solvents and on powder, once dissolved add on oil. Basically keep temp high when brewing all the time.
Tailor
New Member
I have made 10vials of TNE 50mg BA2, BB30. No luck.After 32hrs 5vials crashed.
Put the vials into boiling water for 15-20 minutes and the crystals should go away and brew should remain stable. I don't use vent pins and I'm yet to ever have a vial crack or break. Put something under the vials like a spatula to keep the vials from bouncing around btw. Also every few minutes take the vials out and shake em real good. Do this till all crystals are gone and then boil a few more minutes more for good measure.
Tailor
New Member
10ml vials. I kniow that method with boiling. Don't think it will sray stable for long. Probably for another 30hrs.
Boiling should fix them for good, but you might have to boil them for up to an hour. The 2 vials on left boiled for 30 minutes over a month ago and still good, vial on right not boiled yet. If boiling don't work add more sterile bb to each vial then boil again.
Tailor
New Member
It sounds like I should keep longer in high temp while brewing.
Your one is BA and BB only.
I have BB30% in vials already.
Your one is BA and BB only.
I have BB30% in vials already.
Correct. Did you boil them yet? I'm curious to see if it works or not. Thanks.
Yes mine are just mct oil, ba and bb.
