Test e 400mg/ml experience ?

[rasengan]

Anyone brewed or used test e 400mg/ml ? If yes what was your experience with the pip or experienced any lumps or knots at injection site . Just wanted to know as my distributor is keep asking me for brewing at that concentration as his client demands for it .and I have no idea if its worth it . Don't want to end up throwing 100 of vials in bin

 

[dennia]

I have done it 4 or 5 years ago in a small batch with 2 20%. Pip was the same to 300mg.
Only thing is check if the raw powder don't case any pip firstly.
You can do a small batch for testing and see how it goes. That is what I do when I try something new

 

[NLM36]

I’ve used 400 pip wasn’t bad. I liked it because it allowed me to use less oil

 

[Oroku_Saki]

I made some a few years ago (before the TestE-raw came with PiP from factory) and the pip was bearable, but nothing i would want to use regularly. At least not individually. I have to say, however, that I am quite sensitive to solvents, so it could have been that. If I remember correctly, I used 19/1 at the time.

 

[Dthcore]

I made some a few years ago (before the TestE-raw came with PiP from factory) and the pip was bearable, but nothing i would want to use regularly. At least not individually. I have to say, however, that I am quite sensitive to solvents, so it could have been that. If I remember correctly, I used 19/1 at the time.

What do you use now?

 

[Oroku_Saki]

What do you use now?

15/1 in CSO for almost everything. However, I only use very conservative dosages @200mg/ml for long esters.

With TestE, I didn't use BB at all at 250mg. It was a bit thicker but I tolerated it very well. The shelf life, though, was shortened due to the lack of preservative properties of the BB. I just kept making smaller batches.

 

[Dthcore]

15/1 in CSO for almost everything. However, I only use very conservative dosages @200mg/ml for long esters.

With TestE, I didn't use BB at all at 250mg. It was a bit thicker but I tolerated it very well. The shelf life, though, was shortened due to the lack of preservative properties of the BB. I just kept making smaller batches.

How long do you batches last brother!? This is super interesting lol

 

[Oroku_Saki]

How long do you batches last brother!? This is super interesting lol

What do you mean exactly? How long they last until I need to brew more or until they turn bad?

 

[Dthcore]

What do you mean exactly? How long they last until I need to brew more or until they turn bad?

Both actually!

 

[Jet Labs]

Anyone brewed or used test e 400mg/ml ? If yes what was your experience with the pip or experienced any lumps or knots at injection site . Just wanted to know as my distributor is keep asking me for brewing at that concentration as his client demands for it .and I have no idea if its worth it . Don't want to end up throwing 100 of vials in bin

Test-e 400 will hold just fine at 1/20 and if your raws are good the pip should only be 2-3/10 if you do a full ml shot, but If you mix with something else at 1/1 ratio should be zero pip. As recommended earlier brew a small batch first to gauge pip then go from there.

 

[rasengan]

Test-e 400 will hold just fine at 1/20 and if your raws are good the pip should only be 2-3/10 if you do a full ml shot, but If you mix with something else at 1/1 ratio should be zero pip. As recommended earlier brew a small batch first to gauge pip then go from there.

Yep that's the plan testing with brewing very small batch first raws are on the way let's see how it turns out

 

[Oroku_Saki]

Both actually!

To be honest, only one vial has gone bad so far, TestE without solvent. The vial was hidden at such a stupid angle in my brew closet that I only found it after about two years of bottling. The oil (GSO) has flaked, so it has gone rancid. Unfortunately, I can't say how long it actually lasted.
On the other hand, I have used products that were well over two years old without any noticeable loss of effect. In this case, of course, with at least 15% BB.

How often I brew depends a lot on the consumption of my friends. Testo not quite as often, because I always make a lot of it, as it is usually the basis of everything.
All the other stuff every few months, I would say. It's always quite time-consuming to set up all the equipment, so I like to resist a bit.

 

[canadian mutant]

what are the common carrier oils used for test 400 brews? I got a vial of 400 recently that was brewed in mig840, thought that was kind of strange. But I don’t know shit about 400 brews

 

[rasengan]

what are the common carrier oils used for test 400 brews? I got a vial of 400 recently that was brewed in mig840, thought that was kind of strange. But I don’t know shit about 400 brews

Usually gso,cso,MCT , miglyol840 is good carrier for high mg blends but few people can't tolerate it . I personally love mig840 based oils . Water like thin

 

[canadian mutant]

Usually gso,cso,MCT , miglyol840 is good carrier for high mg blends but few people can't tolerate it . I personally love mig840 based oils . Water like thin

I like the mig. I’ve used it in the past. Just wasn’t sure if it was sketchy that his 400 was in mig. Expected GSO. Sounds like it’s all good tho pip is there but it’s not too too bad. I like the consistency cuz it’s super easy to push out. Gotta change my 18 gauge to 25 gauge pretty quick though or it leaks out when u switch the needles