MESO-Rx
Anabolic Steroids
Test prop homebrew recipe
- Thread starter Anabolicbrah
- Start date
IronBrothers
New Member
Filtered some nasty gear, and pushed 2ml of mct from now sports through the watman to get the residual gear out. Kinda has a funky shimmering look to it, and not so great tasting. Didnt know it had thermogenic properties until I bought some.
hotdog23
New Member
The remainder after hormone BA an BB
9ml hormone
2ml BA
20ml BB
69ml carrier
=100ml
Someone correct me if wrong
The oil is displaced by the powder, you dig brother?
Edit: 4 hours of sleep i may be reading you wrong dog.
Gonna take 10g of powder to make a 100mg per ml batch. Everything else is correct.
hotdog23
New Member
You're right...... 1g of Prop displaces out at .909ml according to the calculator.
I read ya now, yes you are correct!
hotdog23
New Member
Shit boys I'm gonna get it in in few weeks. Can't wait
Your first go round?
hotdog23
New Member
ATodd
New Member
Guys I've been thinking about it, all this displacement crap and what not is fun, but in the end really doesn't matter. I have a scientific background and when I first started brewing everything was perfect. Now I had exactly, (no one fucking knows testosterone)/ml. Unless you're testing the Raws purity, it all means squat. If you've got 10g prop, I would do 70ml. 20% BB, 2% BA, 50% EO, rest MCT (just fill it up to the beaker line). Displacement is unnecessary for such an inexact science. The only thing you really have control over is solvent conc. and total volume. I use 70% as a general guideline for raw purity (way to high in some cases) it going to get you a lot closer to your desired dosage. With the above #'s and the purity actually being 70% you would get:
10g (stuff)/70ml=143mg/ml x 70%= 100mg/ml, but you really still don't know.
Atodd
10g (stuff)/70ml=143mg/ml x 70%= 100mg/ml, but you really still don't know.
Atodd
hotdog23
New Member
Totally agree. Only it would be worthless at that point (to me) with all the EO.. Is there another super solvent that csn replace EO? Guiacol :-/
ATodd
New Member
I don't get what you're saying. You could use guiacol in place, I've never used it for this purpose, just in industry. Smells like a baseball mitt punching clove oil.
Atodd
hotdog23
New Member
For some, myself included, EO in any amount is unbearable, just wondering if it could be replaced. Ya the smell is intense but at least I'd be able to use my high mg brew
ATodd
New Member
If you're allergic to EO, you can use Guiacol or phenyl salicylate to increase solubility. I don't know what conc as I've not used either. But if you can't use EO it's worth looking into.
Atodd
Atodd
iMONSTERoid
New Member
This is how I brew my stuff. I dont use the calculator coz its inaccurate. Once MS of raws are provided I Overdosed the calculation of the Mg/ml I desired upon its purity results. This is a Good Advice!
hotdog23
New Member
Are you able to brew at desired/adjusted concentrations without EO?
Like if purity on test e is 75%, can u get 4g to hold in 10ml with BA/Bb ?
iMONSTERoid
New Member
Depending of the percentage of the purity and the oil carrier. I have tried it without EO just MCT on Test P 50ml of 10g of raw and it crashed w/in 5 hours mark. I added 10ml EO and it holds.I was testing the waters how much will it hold assuming it will so on my next brew ill be doing 80%MCT and 20%EO on a 50% purity of raws.
Due to the lowest purity I began using EO or the thickest oil with Guiacol(for anesthetic)that can hold the raws.
Due to the lowest purity I began using EO or the thickest oil with Guiacol(for anesthetic)that can hold the raws.
Last edited:
20% bb is what it takes to dose it at 100mg/ml.
