The desire to make a blend, Opinions?

[superbane]

I was curious if anyone has had success making a tri blend without any super solvent?

For instance I had this in mind:
75mg ea.
Test | Tren | Mast

MCT oil
1% BA
19% BB

I have seen it done before @
100mg Test Prop
50mg Tren Ace
50mg Mast Prop
GSO oil

Minimal to no PIP at that dosage.

Would this same result be possible with what I had proposed? Opinions?
(Yes I like blends.)

 

[grey]

Would this same result be possible with what I had proposed?

At that BB level it really should not have any issues holding, though I haven't tried making that exact combo.

 

[mghoward74]

I was curious if anyone has had success making a tri blend without any super solvent?

For instance I had this in mind:
75mg ea.
Test | Tren | Mast

MCT oil
1% BA
19% BB

I have seen it done before @
100mg Test Prop
50mg Tren Ace
50mg Mast Prop
GSO oil

Minimal to no PIP at that dosage.

Would this same result be possible with what I had proposed? Opinions?
(Yes I like blends.)

I have made this blend before with short esters. Your ba oil should always be between .9 to 1%. 19% is kind of high imo. Remember your trying to put 200mg in one ml. If you'e not tolerant to prop esters, your going to experience some pip.

Good luck

And no, you don' need any super solvents

 

[superbane]

I have made this blend before with short esters. Your ba oil should always be between .9 to 1%. 19% is kind of high imo. Remember your trying to put 200mg in one ml. If you'e not tolerant to prop esters, your going to experience some pip.

Good luck

And no, you don' need any super solvents

The BA was listed at 1%?
The BB was @ 19%?
I have personally had no problems with Prop esters. When people complain of pip because of esters I am intrigued. I have had pip from what I believe was a poor inj. And the solvents being perhaps too high ?
I've ran test Prop from various sources and have reacted well other than from what I have stated.
I like test prop!

If you do not mind me asking what carrier oil did you use when you made this blend?
I thought 75mg of each compound would be middle of the road. Instead of 50 or 100 of each.

Thank you for the responses.
lol I guess blends aren't too popular.

 

[grey]

I guess blends aren't too popular.

For me, I stopped blending with Tren because I frequently feel the need to adjust how much Tren is in a cycle based on side effects. In a blend this becomes far more difficult than with separately dosed oils.

For Masteron it is the inverse. I like a higher dose per week of Masteron, so almost anything blended in with it ends up being an odd volumetric proportion.

In the end, just simpler (my opinion) to brew 3 batches of different things and do the "blending" as part of the injection process.

 

[master.on]

I was curious if anyone has had success making a tri blend without any super solvent?

For instance I had this in mind:
75mg ea.
Test | Tren | Mast

MCT oil
1% BA
19% BB

I have seen it done before @
100mg Test Prop
50mg Tren Ace
50mg Mast Prop
GSO oil

Minimal to no PIP at that dosage.

Would this same result be possible with what I had proposed? Opinions?
(Yes I like blends.)

I've tried a similar blend but with longer esters
Tren E, Test E, Mast E (I believe EQ was also added)
held perfectly

Unless you really need short esters (i.e. for contest-prep, drug testing)
you can consider longer esters for fail-proof brewing.

 

[superbane]

For me, I stopped blending with Tren because I frequently feel the need to adjust how much Tren is in a cycle based on side effects. In a blend this becomes far more difficult than with separately dosed oils.

For Masteron it is the inverse. I like a higher dose per week of Masteron, so almost anything blended in with it ends up being an odd volumetric proportion.

In the end, just simpler (my opinion) to brew 3 batches of different things and do the "blending" as part of the injection process.

I understand this thought process but ultimately would it not come down to dosage?

If you were to use a tri blend as a base or foundation you could still add different doses of the compounds separately and still end up using less oil in the long haul.

I like to run test:Mast 2:1

Test p / Tren a / Mast p in a blend of 75/75/75mg ea. Per ml would allow me to add or subtract at my preference without the need for ED inj or excessive oil / MLs.

Anyways just what I was thinking about.
I guess the only way to know if it will hold is to try it.

Thank you for all of the input fellas.

 

[grey]

If you were to use a tri blend as a base or foundation you could still add different doses of the compounds separately and still end up using less oil in the long haul.

Yes, as long as I didn't need to adjust my dose of one of those 3 compounds (looking at you Tren!) during the cycle after brewing.

At that point you end up with problems easily avoided by brewing separately.

The amount of oil used/injected has never been much of a concern for me.