MESO-Rx
Anabolic Steroids
Tren Gone Cloudy 1h After Filtering
- Thread starter mic
- Start date
ATodd
New Member
If you are looking for the reason, you are going to have to supply a bit more information that a pic. Which ester, what dosage, what oil, solvents (%). Include some more relavent matierial and we could possibly give you feedback other than maybe they are in front of an a/c vent.
atodd
atodd
fightingfires
New Member
Mine did EXACTLY the same thing.
Tren A powder from Chinese source.
Made 50ml
100mg/ml
gso
2% ba
20%bb
and also filtered with .22 syringe filter
yellow but clear after filtering, then next day I looked and cloudy
so you are not alone brother!!!
I have Labmax kit but still waiting on light to test it
Melt point was bang on though
Tren A powder from Chinese source.
Made 50ml
100mg/ml
gso
2% ba
20%bb
and also filtered with .22 syringe filter
yellow but clear after filtering, then next day I looked and cloudy
so you are not alone brother!!!
I have Labmax kit but still waiting on light to test it
Melt point was bang on though
fightingfires
New Member
ya got me man....I will be at least testing mine when the light gets here.
I also have some finaplix and component TH to convert to compare it too when I test it
I also have some finaplix and component TH to convert to compare it too when I test it
ATodd
New Member
Looks good from the ingredient and conc. aspect. The only thing I can think of is maybe what ever was in the raw that wasn't tren (because it wasn't %100 pure) is slightly soluble in oil at the higher temps you used to dissolve and fell out after it cooled. I would say refilter. Whatever was tren should be dissolved with that level of BA and BB. This is why in the industry we always filter cooled products. I realized it's more difficult if not impossible with these products and instruments.
atodd
atodd
ATodd
New Member
Are you using syringe filters? It's easier using the auto fills. But if you haven't made that much, the syringe will work, just tough on the hands. I've heard people use a bigger syringe and a caulk gun.
atodd
atodd
fightingfires
New Member
Here is a good tip I discovered when pushing through a filter with a caulking gun...
Lets say you have a 100ml syringe and 50 ml of product. Make sure you have the oil in the syringe along with 10-20ml of air. That way when you apply pressure with the caulking gun the air gets a bit compressed. If there is no air it is easy to blow out the filter as oil has little if any compression ability.
Lets say you have a 100ml syringe and 50 ml of product. Make sure you have the oil in the syringe along with 10-20ml of air. That way when you apply pressure with the caulking gun the air gets a bit compressed. If there is no air it is easy to blow out the filter as oil has little if any compression ability.
ATodd
New Member
That actually makes alot of sense. Kudos. If I ever use the syringe filters that tidbit will be put to use.
atodd
Halotestinluver11
Banned
Hello sir, how long approximately will it swirling it in the beaker for the the powder dissolve in the oil and solvents and the soultion is completely homogeneous and clear? 20-30mins? without using heat method
ATodd
New Member
I have no idea. Lab work in which i would disolve solids in other components first to hasten the dissolution. When mixed in large vats, sometimes days. If you are going to go that route, I'd mix the powder with the BA and BB first until you think no more can go in, then mix in the oil. i don't think heat is a bad thing at low incriments.
atodd
Should be fine. Tren ace can be cloudy, its no issue
nophat
Subscriber
Post in your own thread bro.
I think you got prop!
How well do you know you supplier ?
I think you got prop!
How well do you know you supplier ?
hey OP can you name the source please!
nophat
Subscriber
Tren cloudy ok!
Really try again.
Really try again.
Would you pin it?
Similar threads
