TrNE problems

[Infidel141]

So I've been reading up on brewing. This past week I've started getting the ball rolling. I brewed some test e, prop, and npp with no problems so far. I have not pinned them yet so I can't speak on pip if there is any, nothings crashed though.
On to my problem, I am in the process of Trne. I kind of went off of @ickyrica post in the @raped ape thread on tne. Was for 50mg/ml, his recipe was 1/40/5 ba/bb/gua.
I went with 100mg/ml 1/40/10 with 3g of raw, carrier split 50/50 gso/eo. Got everything in and was stirring with low warmth most dissolved but still had some powder in it. I had to leave so I covered it to sit, came back and most of it is crashed. I have no idea where to go from here, if anyone could chime in and get me on the right track I'd really appreciate it.

 

[ickyrica]

It's fixable. When I'm at my office I'll do a little math. Well get you in a good spot

 

[ickyrica]

So I've been reading up on brewing. This past week I've started getting the ball rolling. I brewed some test e, prop, and npp with no problems so far. I have not pinned them yet so I can't speak on pip if there is any, nothings crashed though.
On to my problem, I am in the process of Trne. I kind of went off of @ickyrica post in the @raped ape thread on tne. Was for 50mg/ml, his recipe was 1/40/5 ba/bb/gua.
I went with 100mg/ml 1/40/10 with 3g of raw, carrier split 50/50 gso/eo. Got everything in and was stirring with low warmth most dissolved but still had some powder in it. I had to leave so I covered it to sit, came back and most of it is crashed. I have no idea where to go from here, if anyone could chime in and get me on the right track I'd really appreciate it.

Assuming you tried to make 30ml? Do you have anymore tren base?

 

[ickyrica]

So this is where my math takes me

you currently have:
.3ml BA
12ml BB
3ml GU
3g raw
remainder is carrier oil

you have a strange GU ratio here, and the overall % of the trne is going to keep giving you issues. drop that to 50mg/ml. that's going to pack one heck of a punch man. It hits hard.

The easiest way to achieve this is pretty simple, you need to reach 60ml total volume when you are finished (in comparison to the raws that have already been used)

your GU % is already where you want it so no need to add anymore of that stuff. you want to double your BA & BB percentages so add .3ml of the BA and 12ml of the BB. (for a total of .6ml BA - 24ml BB - 3ml GU)

now, you will have a small amount that needs to be added to hit the 60ml mark. Maybe about 16/17ml remaining. That is going to be filled with carrier.

Does this make sense? What I am doing is using the raws and GU percentages that you have used to adjust the BA, BB and carrier amounts to hit a % that can be reliable. I do not know how to go higher than 50mg/ml because that is waaaay more than I have ever needed at one time.

 

[Infidel141]

Yes make sense to me I was trying to figure last night how to just drop the mg down, but it just wasn't clicking with me. I'll give that a try and see what happens.

 

[Infidel141]

Assuming you tried to make 30ml? Do you have anymore tren base?

Well 27 but yea 30 no I don't have anymore

 

[Infidel141]

@ickyrica should I go with eo for the rest of the carrier or keep it 50/50

 

[ickyrica]

@ickyrica should I go with eo for the rest of the carrier or keep it 50/50

Up to you man. I don't think that matters so much. Personal choice basically

 

[ickyrica]

@ickyrica should I go with eo for the rest of the carrier or keep it 50/50

Let me know how it works out.

 

[Infidel141]

This is what I got from that man, hasnt change much from how it was before I'm not sure how long this compound takes to dissolve. Been about 20 minutes

 

[Infidel141]

So update, got it all dissolved. Gonna let it sit and see if it crashes again.

 

[ickyrica]

So update, got it all dissolved. Gonna let it sit and see if it crashes again.
View attachment 94052

Brewing should be approached with patience. I know we all use heat to help speed things up, which is typically fine to do. Just give it time

 

[Infidel141]

First time for me brewing. Now I know what to expect, first couple compounds just went fairly quick. I figured that one would be the same. Thanks for the advice brotha. I'll post how it is later!

 

[ickyrica]

First time for me brewing. Now I know what to expect, first couple compounds just went fairly quick. I figured that one would be the same. Thanks for the advice brotha. I'll post how it is later!

Way to work dude. If that holds fine you should be approximately 50mg/ml. Use long pins, you don't want base going sub Q

 

[Iron Vett]

Way to work dude. If that holds fine you should be approximately 50mg/ml. Use long pins, you don't want base going sub Q

I'm about to try to brew some TrNE and was wondering about the heat needed for tren base to easily go into solution. Is it like tren a where a little heat does fine or does it take quite a bit more heat? Is tren base susceptible to oxidation from heat like tren a and e is?

 

[ickyrica]

I'm about to try to brew some TrNE and was wondering about the heat needed for tren base to easily go into solution. Is it like tren a where a little heat does fine or does it take quite a bit more heat? Is tren base susceptible to oxidation from heat like tren a and e is?

just a little heat, some time and the solvents man.

 

[ickyrica]

First time for me brewing. Now I know what to expect, first couple compounds just went fairly quick. I figured that one would be the same. Thanks for the advice brotha. I'll post how it is later!

how are you holding up?

 

[Infidel141]

how are you holding up?

It's crashed again, not a lot but I can see it. Also its swirly like I can see the eo in it or something

 

[ickyrica]

It's crashed again, not a lot but I can see it. Also its swirly like I can see the eo in it or something

I would put it back on heat, maybe a little hotter than when you first brewed it. Not too hot, but the time I would heat it would be around 30 minutes or so. Stir the batch almost the entire time, like a steady stir. Doesn't have to be agitated much. I'm willing to bet that a little more heat and a thorough mixing will finish you up.

I would refrain from adding anymore to it until this step is exhausted and you still have issue. I don't think you will need to do more than thia though

 

[ickyrica]

Any positive change?