20 g test cyp at 200 mg/ml = 100 mL
100 mL
18 BB
2 BA
18.18 displacment
= 38.18
61.82 mL MCT oil
100 mL
18 BB
2 BA
18.18 displacment
= 38.18
61.82 mL MCT oil
MESO-Rx
Anabolic Steroids
Test Cyp brew
- Thread starter jJjburton
- Start date
Night_Owl
Member
@jJjburton thanks man
Cakedup
Subscriber
Some clown on here yesterday was telling me what's on us should I say he was making test C 250 with
2%BA,
18%BB in MCT oil.lol
What about test P 150 using MCT?
2%BA
18%BB
10%EO???
I have never brew test p or used EO. Sorry
TRT@40
Member
hey bud, what's wrong with the above test c 250mg/ml recipe? seems right. I don't understand what you mean.
I don't have much to add to your test p recipe question other than that 150mg/ml seems a little high of a concentration. I am interested in an answer to your question as well but I am gonna start with 100mg/ml first before trying higher concentration of it.
Cakedup
Subscriber
Test P 100mg it's,
2%BA
14%BB
Carrier=MCT
Also
Test P 150mg
2%BA
12%BB
Carrier=Mig840
But I wanna try 150mg without Mig840, but using MCT instead..
Thx for responding tho brother....
Cakedup
Subscriber
Nothing if your talking about this recipe, but it's Test C 200mg
20 g test cyp at 200 mg/ml = 100 mL
100 mL
18 BB
2 BA
18.18 displacment
= 38.18
61.82 mL MCT oil
You can't make Test C 250mg with this using MCT or it will crash in a few days after you vial it. Unless you keep it in a room above 78-82°F. You need EO for TC 250mg or higher. However you can make Test E @500mg using this exact recipe.
TRT@40
Member
Thanks for sharing test p recipes.
How is the pip with test p 150mg/ml recipe¿ I just picked up some mig840 from amazon so I might try your recipe .
About test cyp at 250mg/ml, I bought few vials made with mctoil from TGI. It has not crashed and has no pip. But I don t know the ba and bb content; perhaps he used higher % of bb.
FLTestlab
New Member
Thanks a lot for this info bud!
Cakedup
Subscriber
No because the highest you could use would be 20% without causing irritation so what you did was had it between 5 to 10% EO.
If you guys ever need a recipe for anything just lmk.
I also have one for every compound using Mig840....
Glad to be part of a good community so I'm more than willing to give back..
TRT@40
Member
Thanks for clearing that up. I was told by a source here that alpha pharma also uses 10% eo in their oil. I have found AP oils to be very smooth.
So you are suggesting the following for 250mg/ml test cyp recipe in mct oil ?
2 % ba
20 bb %
5-10 % Eo
Rest mct oil
What would you recommend for primo e with highest concentration without pip and with mct , eo or mig840 or the combo of 3 but without guac?
I’m afraid I’m going to have to disagree with you on 1/18 not working for test cyp. I’ve been using this recipe for quite some time and the only vial that has ever crashed was in a building with no heat and the temps got down into the high 20’s F. I know that it has been exposed to low 40’s F and it quite possibly could have been high 30’s F and none crashes. I do live in an area that is near sea level and that may play a role in the lower possibility of crashing but that is part of the fun of home brewing. Finding out what works for you.
Cakedup
Subscriber
I don't disagree with you brother I have had some test C that didn't crash at 250mg, but like I said before it depends on where you live and what the temperatures are like and where you store it. I mean I personally make my own test e 300 with only 4% BB and test E-250 with no BB at all.
Swolemonkey86
Member
I made cyp 250 with 2%BA and 20%BB with just MCT and the shit doesn’t crash at all. I do live in California though so the temps never get really low.
I think 125 will hold, but not 150 if MCT (Mig810)
150 if half Mig810/ half Mig840 probably will hold. If all Mig810, it'll hold for sure.
Cakedup
Subscriber
That's what I have correct for the 150 I have the carrier as mig840. However I did just noticed that I had to be be content and I think I have my recipe book right here to check but I have it at 12% here and I want to say it's harder than that let me look. No I was right 12% will hold. As you know but I'm sure a lot of guys that are learning might not. Another big part of it holding is the mixing and heating process. If you mix your Raw with your solvents only until it's completely dissolved, using have magnetic hot plate with a stir rod. So that the Raw is completely suspended into the solvents first, and then adding your carrier in this case mig840. Personally I found the faster I like Spin and stir up and the longer at the proper temperature the much less chance that has and crashing. Especially if we're talkin about compounds like DHB, Tren base or Test and Tren BASE. Things that like the crash. Would you agree with this Theory As It Seems to work for me most of the time anyway.lol
I've been trying to change a lot of my recipes from Mig840 to just MCT. Just because it's becoming too expensive, and more difficult to obtain lately. Therefore I'm going to try that Test P 150mg with MCT using,
2%BA
18-20%BB
What's your take on that?
And did you get my wire last night?
I think you have me confused with someone else bro!! LoL all good though. I'm actually not even a brewer; just going off my personal knowledge from speaking with people that do!!
Using soon
Note self
22 and 25
8 30 ML
22 and 25
8 30 ML
Cakedup
Subscriber
I don't know maybe I do I thought you used to be on ASF a lot. Either way doesn't matter, but what does matter is I think you have some things backwards. Original post you said it would hold at 150mg with a mixture 50/50 Mig810 and Mig840. Then said it would definitely hold with 100% Mig810. Mig810 is just triglycerides of fractionated C8 and C10 which is MCT oil. Mig840 however has propylene glycol derivatives which make it a lot easier to hold compounds at a higher MG...
