Cloudy tren

[themanhart]

Hey

Bought some tren ace from Aaster Solutions and it looks like homebrew

All the oil contains cloudy swirls

Does it matter?

 

[Skarpyona]

I would pass it through a .22 filter just incase if you're really worried about it. You never know what safety measures UGL take, if any at all.

 

[themanhart]

I would pass it through a .22 filter just incase if you're really worried about it. You never know what safety measures UGL take, if any at all.

Ya better 'safer' than sorry right?

 

[lifter6973]

I would not pin it at all. Contact whoever the fuck that is (never heard of them) and ask for a replacement or your money back.

 

[RoidRage420]

The best tren I have ever used in all my years was cloudy. Shit was fucking wild. Up to you to pin it but from personal experience you'll be fine provided it was filtered

 

[Bulldog413]

Warm it between 90f - 110f for about 10 - 15 min and see if it clears up. That rules out impurities.

 

[themanhart]

Warm it between 90f - 110f for about 10 - 15 min and see if it clears up. That rules out impurities.

And I won't risk destroying the compound itself?

 

[Skarpyona]

And I won't risk destroying the compound itself?

50 degrees Celsius is considered safe for the hormone, which is ballpark what bulldog mentioned

 

[Bulldog413]

And I won't risk destroying the compound itself?

My home brew did the exact same thing. I used 2% and 20%. I overdosed about 12-15 % so that may have contributed to my cloudyness. Warming mine up clears it up good and shiny. But it clouds just like yours after about 30min after cooling.

 

[themanhart]

My home brew did the exact same thing. I used 2% and 20%. I overdosed about 12-15 % so that may have contributed to my cloudyness. Warming mine up clears it up good and shiny. But it clouds just like yours after about 30min after cooling.

Interesting.. Well, fingers crossed

 

[master0n]

seems crashed, crystalization will have clear shard like crystals in the solution. it's usually a result of too much active ingredient and not enough oil to hold it in a suspended state. as the temperature go's down the solubility of the powder decreases as well and that's when crystalization starts.
heat it up a little bit and it should g2g

 

[themanhart]

seems crashed, crystalization will have clear shard like crystals in the solution. it's usually a result of too much active ingredient and not enough oil to hold it in a suspended state. as the temperature go's down the solubility of the powder decreases as well and that's when crystalization starts.
heat it up a little bit and it should g2g

Well thanks

 

[MindlessWork]

I know this is an old thread but it seems the Naps thread also has many references to this lab....

 

[ghibli]

My home brew did the exact same thing. I used 2% and 20%. I overdosed about 12-15 % so that may have contributed to my cloudyness. Warming mine up clears it up good and shiny. But it clouds just like yours after about 30min after cooling.

Sorry for the random message from an old thread! Recently had this happen to a brew. Haven't had time to inject it. Is there more pain when injecting this when it looks like this?

Not sure if I should toss this batch out or if its all good like you said. I did the same 20% 2% with a 2% overdose on 100mg. Also @themanhart have you tried it? Any reports on swelling or more PIP?

 

[Bulldog413]

Sorry for the random message from an old thread! Recently had this happen to a brew. Haven't had time to inject it. Is there more pain when injecting this when it looks like this?

Not sure if I should toss this batch out or if its all good like you said. I did the same 20% 2% with a 2% overdose on 100mg. Also @themanhart have you tried it? Any reports on swelling or more PIP?

I tossed it all. Never used it.

 

[bnp2]

I used a few ML of this cloudy tren before I realized it looked like this . I was fun bit am scared to keep using it lol

 

[bnp2]

I used a few ML of this cloudy tren before I realized it looked like this . I was fun bit am scared to keep using it lol

 

[Killze022]

Caused by moisture in the brew.

 

[Schibetta]

Hey

Bought some tren ace from Aaster Solutions and it looks like homebrew

All the oil contains cloudy swirlsView attachment 143633

Does it matter?

Crashed heat that shit up.

 

[bnp2]

Caused by moisture in the brew.

So is it okay