MESO-Rx
Anabolic Steroids
making testosterone without magnetic stirrer
- Thread starter evil666
- Start date
Ridethelightningbarefoot
Member
Idk never done it. Ive heard of people letting it sit over night. If you have any powder that doesnt fall into solution it will just be crystals in solution or get filtered out. There is no reason not to just get a basic set up: single electric table top element, beakers, glass stir rod, syringe filters, caulk gun. You dont need the table top burner if you have a stove. Heat is key. Is it cost thats a issue for you?
theotherguy
Member
My first couple of brews I used a sauce pan on a stove top, heated the pan up on low heat, and swirled the beaker around in the pan. I very quickly realized it was a huge PITA so I dropped $55 on a magnetic stirrer with hotplate on eBay. It was cheap, but it works just fine so far, and I have made probably 2 dozen brews with it
Ridethelightningbarefoot
Member
Does your stir plate have a magnetic piece you have to put in the brew? Also have got a vacuum set up yet?
theotherguy
Member
Yes, I use the magnetic stir bars in the brew. I have been dragging my feet on the vacuum set up lol. The caulking gun and syringe is tedious, but easy
Yes, definitely possible. I brewed just about everything under the sun before I got a magnetic stirrer. Definitely easier with than without...
I use a dry heat iron and turn it around if i need heat. Lol but a just swirl the beaker on the iron
Coffee cup warmer at 130F and a sterile kitchen spoon will make Test just fine.
I would like to try to make the test without magnetic stirrer. In the future I will buy magnetic stirrer
Robby550
Member
Can I ask what brand and model you got? I'm about to grab one myself
Ridethelightningbarefoot
Member
You dont need one. I was talking about a glass stir rod. They are very cheap like a few bucks
Ridethelightningbarefoot
Member
Im sure its not a big deal but I dont think I would ever put anything metal in my brew. That is other than the syringe. Its probably compulsory but thinking about potentially injecting metals makes me cringe haha.
theotherguy
Member
I didn’t get this exact one, but I couldn’t find the one I bought. But this is more or less the same one
Ok, I understand now, thank you. In my country the cost of glass stir rod is like 0,50$. very cheap
I hear you but if the brew was somehow able to start dissolving the spoon I think there would be larger issues
For something like test-e, I usually melt the powder into a liquid in the beaker then start adding the solvents and oil. I just stir using a syringe with cap on (since its sterile). I might even stick the solution in the microwave for a couple seconds to heat it up. The solution should turn crystal clear, and be a single color.
Deadp007
Member
How do you all sterilize the magnetic stir bar?
The stirrers are pretty simple even if all you have is alcohol to submerge them.
Lil_swole87
New Member
I hard you can put it in the oven at 200f as low as it goes and leave it in there for 30/45 seconds then take out and it works good.. or even instead of a water bath has anyone tried using oil bath to break it down 1st then a blow-dryer to keep it warm in the Syringe barrel when they filter it. so its easy to pass through the filter ..... ? Any Thoughts guys on theses ideas lol
D
Deleted member 123722
Guest
Idk how you guys do it, but my buddy who runs his own lab told me to put the solvents and powder in a beaker FIRST; let them break down the powder into a liquid; then heat that up in the pan; and finally, add oil in the beaker LAST, while it is in the pan.
At first it may seem the solvents alone are not enough to liquify the raws, but they are...
That's how I've done all my brews, and I have had zero crashes, no PIP, and it's very easy to have warm oil go through the syringe and filters.
At first it may seem the solvents alone are not enough to liquify the raws, but they are...
That's how I've done all my brews, and I have had zero crashes, no PIP, and it's very easy to have warm oil go through the syringe and filters.
