MESO-Rx
Anabolic Steroids
Test C with white cloudy swirls and sediment in the bottom of vial??
- Thread starter nighthawkmuscle
- Start date
Greenbay68
Member
Looks like it’s starting to crash. Put it in a ziplock baggy and dip into hot water, near boiling for a minute or two. Should go back into suspension.
Sapopeluo
Subscriber
To be honest, I cannot distinguish in the pictures whether looks like Cristal (if so, just stirring it up in a bio with hot water will suffice to remix)…
But in case it looks gelatinous… then I suggest just discarding it…
phenominal34
Banned
Put it on a candle warmer, after 5 mins shake it. See if it clears up.
nighthawkmuscle
New Member
It did go back into solution after multiple hot water baths and at least an hour, But the sediment definitely didn’t look like crashed gear. Anyone think it could be bacteria growth? Would that go into solution with constant shaking and heating?
lukiss96
Member
If it doesn't I would not risk it. Looks high concentration possibly bad pip.
Jerdboben
Member
If available, previous Jano results would verify if it's high concentration? What's up with the "sediment" though?
Greenbay68
Member
Highly doubt bacteria growth. Do you have unopened vials like this? In a fresh vial, there is no medium for bacteria to grow on, let alone in an environment with alcohol.
Regardless, I'd contact the vendor with pics, let them know you reheated and it won't stay in suspension. Good vendors will send replacements.
OldGHGuy
Member
Pitch it...why take a chance?
Spaceman Spiff
Subscriber
Put it on a candle warmer, after 5 mins shake it. See if it clears up.
After homebrewing and crashing stuff. This looks like k am gonna second this. Looks like it may be fine, just on the edge of crashing. Like 1% more BB and it would be fine.
Heat it and shake it
After homebrewing and crashing stuff. This looks like k am gonna second this. Looks like it may be fine, just on the edge of crashing. Like 1% more BB and it would be fine.
Heat it and shake it
bighunanballs
Member
It's crashing and to mimic what some are saying in here, what will happen if you heat and get it dissolved again, is that it will come apart after you inject causing pip and prob swollen lump at injection site. This seems to always happens to me when I inject gear on the verge of constantly crashing at room temp.
Spaceman Spiff
Subscriber
I feel like some stuff may take a week to recrash. If it takes that long to recrash, it's usually fine
bighunanballs
Member
indeed youre prob right. i only recall having issues with stuff that starts crashing pretty much right after heating and re-dissolving. usually if i see white streaks a few hours after heating and re-dissolving i know its gonna hurt like a B after i inject. ill usually dilute it down with another hormone if i can or just rebrew it a little and add some bb or water it down (with carrier oil of course)
nighthawkmuscle
New Member
It’s stayed in solution after being re-heated yesterday, so I think it will be gtg. Just hadn’t seen those white swirls or ‘sediment’ before but it must be crashed gear
nightprowler7
Member
I actually got some vials from qsc that looked just like this. I tried heating it and nothing changed so I threw it away
Jerdboben
Member
Damn, you got me worried now. I stocked up on their test c during the promo. I'll post a pic after I receive them.
Greenbay68
Member
I got test C from them recently and it arrived crashed. I am in a cold location though, so not rare. Quick bath and they're good. They stayed in suspension for a few weeks now. Test C at 250mg should be very stable at the correct temperature. I've never had to reconstitue Test C or E more than once.
Other things like Primo 200, TNE and Deca 400 have given me issues over the years.
Similar threads
