anubisascended73
New Member
Best test cyp 250 recipe with Mig 812
MESO-Rx
Anabolic Steroids
Best test cyp 250 recipe with Mig 812
- Thread starter anubisascended73
- Start date
dinfaralt
Member
just try basic 27,5g test, 2ml ba, 10ml bb, 88ml oil and adjust while you're brewing depending on your comfortability.
if i can give one tip is to add in slowly if you're new brewer if you have subpar equipment it helps with less mixing hassle later
I would do 2/22 or 2/24 if it's stored and shipped in cold environments.
It isn't the best recipe; it's a recipe that works. I can't point out what the best recipe, best oil, best injection place, best needle length, or gauge is. It's what generally works and what's best for you.
Use a homebrew calculator to find out exactly how much of each you need
It isn't the best recipe; it's a recipe that works. I can't point out what the best recipe, best oil, best injection place, best needle length, or gauge is. It's what generally works and what's best for you.
Use a homebrew calculator to find out exactly how much of each you need
Ghoul
Member
I’ve got you bro.
Mig 812
Alternating delts
BD 1/2” 27g
You’re welcome.
anubisascended73
New Member
Was really looking for opinions on bb% with mig 812 and or adding another carrier oil
It isn't one-size-fits-all. There are a lot of variables.
It's about what generally works and what works best for you. You will find that out in time through trial and error.
For example, a friend can't use mig812, and I'm not in love with it either. I can't pin delts only as the volume of oil is too high, and with 1/2 needles, it isn't smart to use to pin 2.5 or 3ml.
Things aren't black or white, nor is there just one way to do things.
But for what this guy wants, it's a good recipe, but the best recipe or the universally best is a utopia. Some guy I read on this forum can't use BB. It's a rare case, but it exists. For that guy, this recipe is terrible, and this ester is terrible because it can't be brewed without some BB.
Ghoul
Member
Was just kidding 
What doesn’t work for you with 812 out of curiosity?
What doesn’t work for you with 812 out of curiosity?
Sometimes I get inflammation and a minor PIP; sometimes it's fine. I don't know why, but out of 10 injections, 4 or 5 give me issues.Was just kidding
What doesn’t work for you with 812 out of curiosity?
My friend, on the other hand, can't use it at all. It gives him inflammation and PIP comparable to what notorious Test E gives.
Nowadays, I use 100% EO or a mix with castor oil. But that's just me.
Some get PiP by EO in gear
xrayphoton13
Member
My recipe book says 25% bb/2% ba. If you go up to cyp 300 then 30/2. Should keep it from crashing
Alexthemutant
Member
this would not produce 270 mg per ml?
dinfaralt
Member
most testosterone cyp on the market is around 90% purity right now.
so at 90% purity you will get 248mg/ml
vs risk of getting 270mg/ml
i take it.
its upto you man but i better be having something around 250mg/ml - 270mg/ml end product for trt than 225mg when its 10% underdosed.
im too cheap so im only testing end product with 2-3 different oils in my vial when im done brewing. thanks to the guy that learned me that life hack
Alexthemutant
Member
yes correct that makes sense : )
If it is for you and you can tolerate miglyol then great.
There are many who cannot use miglyol
Lumps welts and inflammation
I use miglyol 840 in my brews
Can pin with 27ga if I want
Nice stuff
powerandmuscle
New Member
My Test Cyp 250mg brew: 2%BA, 15%BB, Rest Mig 812. I personally don't like the mig 840.
250 cyp
25% BB with thinner oil is ideal
The thinner your oil the more solvent you actually need
Holding power isn't just solvent concentration but also viscosity related
25% will be enough for even a cold transport
But you can do 20% easily but since your using thin mig 812 I recommend 25%
Assuming your vials never get cold correct? I find in the winter vials need a little extra babying or more solvent to hold long term. 15% Is low for 250. I assume you never get a crash. Do you keep them in warm place? I personally did 18% BB in mig 812 and my 250 crashed pretty hard. Had to go to 20% for it to hold.
Similar threads
- Question
